manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 19

Introduction

1

5977B Series MSD Troubleshooting and Maintenance Manual

19

Important Safety Warnings

There are several important safety notices to keep in mind when using the 
MSD.

Many internal parts of the MSD carry dangerous voltages

If the MSD is connected to a power source, even if the power switch is off, 
potentially dangerous voltages exist on:

•

The wiring between the MSD power cord and the AC power supply, the AC 
power supply itself, and the wiring from the AC power supply to the power 
switch.

With the power switch on, potentially dangerous voltages also exist on:

•

All electronics boards in the instrument

•

The internal wires and cables connected to these boards

•

The wires for any heater (oven, detector, inlet, or valve box)

Electrostatic discharge is a threat to MSD electronics

The printed circuit boards in the MSD can be damaged by electrostatic 
discharge. Do not touch any of the boards unless it is absolutely necessary. If 
you must handle them, wear a grounded wrist strap and take other antistatic 
precautions. Wear a grounded wrist strap any time you remove the MSD right 
side cover.

WA R N I N G

All these parts are shielded by covers. With the covers in place, it should be difficult 
to accidentally make contact with dangerous voltages. Unless specifically 
instructed to, never remove a cover unless the detector, inlet, or oven are turned off.

WA R N I N G

If the power cord insulation is frayed or worn, the cord must be replaced. Contact 
your Agilent service representative.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands