manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 214

214

5977B Series MSD Troubleshooting and Maintenance Manual

8

Electronics

Side Board

The side board is mounted on the side plate. It performs these functions:

•

Provides the 1 MHz reference clock for the RF amplifier.

•

Generates the RF component of the voltage applied to the quadrupole mass 
filter according to a signal from the main board. The amplitude of this 
voltage is proportional to the mass selected.

•

Generates the DC component of the voltage applied to the quadrupole mass 
filter. The magnitude of this voltage is proportional to the RF voltage.

•

Passes voltages generated on the main board and the detector focus voltage 
from the HED power supply to elements in the ion source and the detector.

•

Generates and adjusts filament emission current and electron energy as 
controlled by the main board.

•

Switches the filament power from one filament to the other.

•

Monitors for RF faults and shuts down the analyzer if one is detected.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands