manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 49

General Troubleshooting

2

5977B Series MSD Troubleshooting and Maintenance Manual

49

Pressure Symptoms

This section describes unusual pressure readings and their possible causes. 
The symptoms in this section are based on typical pressures. At typical 
column flow rates (0.1 to 2.0 mL/minute), the foreline pressure will be 
approximately 20 to 100 mTorr. The analyzer chamber pressure will be 
approximately 1 × 10

-6

 to 1.4 × 10

-4

 Torr. These pressures can vary widely from 

instrument to instrument so it is very important that you are familiar with the 
pressures that are typical for your instrument at given carrier gas flows.

The analyzer chamber pressures can only be measured if your system is 
equipped with the optional gauge controller.

Foreline pressure is too high

If the pressure you observe for a given column flow has increased over time, 
check the following:

•

Column (carrier gas) flow is too high

•

Air leak (usually the sideplate is not pushed in or vent valve is open)

•

Foreline pump oil level is low or oil is contaminated (standard foreline 
pump)

•

Foreline hose is constricted

•

Foreline pump is not working correctly

Analyzer chamber pressure is too high (EI operation)

If the pressure you observe is above 1.0 × 10

-4

 Torr, or if the pressure you 

observe for a given column flow has increased over time, check the following:

•

Column (carrier gas) flow is too high

•

Air leak

•

Foreline pump is not working correctly (see 

Foreline pressure is too high

)

•

Turbo pump is not working correctly

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands