manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 200

200

5977B Series MSD Troubleshooting and Maintenance Manual

7

Analyzer

Filament care

Similar to the filaments in incandescent light bulbs, the ion source filaments 
will eventually burn out. Certain practices reduce the chance of early failure:

•

If you have an optional G3397B Micro-Ion vacuum gauge, use it to verify 
that the system has an adequate vacuum before turning on the analyzer, 
especially after any maintenance was performed.

•

If you are controlling your MSD from the 

Manual Tune

 screen, always select 

MSOff

 before changing any of the filament parameters.

•

When setting up data acquisition parameters, set the solvent delay so that 
the analyzer will 

not

 turn on while the solvent peak is eluting.

•

When the software prompts 

Override solvent delay

?

 at the beginning of a run, 

always

 select 

NO

.

•

Higher emission current reduces filament life. 

•

Higher electron energy reduces filament life.

•

Leaving the filament on for short times (

1 minute) during data acquisition 

reduces filament life.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands