manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 94

94

5977B Series MSD Troubleshooting and Maintenance Manual

4

General Maintenance

An oil trap is supplied with the standard foreline pump. This trap stops 

only

 

pump oil droplets. It 

does not

 trap any other chemicals. If you are using toxic 

solvents or analyzing toxic chemicals, do not use this oil trap. For all foreline 
pumps, install a hose to take the exhaust from the foreline pump outdoors or 
into a fume hood vented to the outdoors. For the standard foreline pump, this 
requires removing the oil trap. Comply with your local air quality regulations.

The fluids in the DP and standard foreline pump also collect traces of the 
samples being analyzed. All used pump fluid should be considered hazardous 
and handled accordingly. Dispose of used fluid correctly, as specified by your 
local regulations.

Electrostatic discharge

All of the printed circuit boards in the MSD contain components that can be 
damaged by electrostatic discharge (ESD). Do not handle or touch these 
boards unless absolutely necessary. In addition, wires, contacts, and cables 
can conduct ESD to the electronics boards to which they are connected. This is 
especially true of the mass filter (quadrupole) contact wires which can carry 
ESD to sensitive components on the side board. ESD damage may not cause 
immediate failure, but it will gradually degrade the performance and stability 
of your MSD.

When you work on or near printed circuit boards, or when you work on 
components with wires, contacts, or cables connected to printed circuit 
boards, always use a grounded antistatic wrist strap and take other antistatic 
precautions. The wrist strap should be connected to a known good earth 

WA R N I N G

The oil trap supplied with the standard foreline pump stops only foreline pump oil. It 
does not trap or filter out toxic chemicals. If you are using toxic solvents or 
analyzing toxic chemicals, remove the oil trap. Do not use the trap if you have a 
CI

 

MSD. Install a hose to take the foreline pump exhaust outside or to a fume hood.

WA R N I N G

When replacing pump fluid, use appropriate chemical-resistant gloves and safety 
glasses. Avoid all contact with the fluid.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands