manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 156

156

5977B Series MSD Troubleshooting and Maintenance Manual

6

Vacuum System

Common Vacuum System Problems

Air leak symptoms

The most common problems associated with any vacuum system are air leaks. 
Symptoms of air leaks include:

•

Loud gurgling noise from the foreline pump (very large leak)

•

Inability of the turbo pump to reach 95% speed

•

High foreline pressure in diffusion pump MSDs

•

Higher than normal high vacuum gauge controller readings

The 5977B Series MSD will 

not

 pump down successfully unless you press on 

the side plate (analyzer door) when you turn on the MSD power. Continue to 
press until the sound from the foreline pump becomes quieter.

Pumpdown failure shutdown

The system will shut down both the high vacuum and the foreline pump if the 
system fails to pump down correctly. Two conditions that trigger shutdown 
are: 

•

Diffusion pump MSDs, shutdown occurs if the foreline pressure is above 
300 mTorr after 7 minutes.

•

Turbo pump MSDs speed below 80% after 7 minutes.

This is usually because of a 

large

 air leak: either the side plate has not sealed 

correctly or the vent valve is still open. This feature helps prevent the foreline 
pump from sucking air through the system, which can damage the analyzer 
and pump.

To restart the MSD, find and correct the air leak, then switch the power off 
and on. Press on the side plate when turning on the MSD power to ensure a 
good seal.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands