manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 103

General Maintenance

4

5977B Series MSD Troubleshooting and Maintenance Manual

103

7

Using a T-20 Torx screwdriver, tighten the lock plate by turning the lock 
plate screw counter clockwise.

8

Install the 9000 GC/MSD Tail.

9

If the MSD is equipped with a MFC, attach the MFC gas lines.

Figure 7  

GC/MSD interface and bus

C A U T I O N

Do not turn on any GC heated zones until carrier gas flow is on. Heating a column with 
no carrier gas flow will damage the column.

C A U T I O N

During pumpdown, do not push on the filament board safety cover while pressing on 
the analyzer boards. This cover was not designed to withstand this type of pressure.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands