manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 170

170

5977B Series MSD Troubleshooting and Maintenance Manual

6

Vacuum System

The diffusion pump transports gas by momentum transfer. The heater boils a 
special fluid (a polyphenyl ether) inside the stack. As the vapor pressure 
increases, the pump fluid vapor is forced out and downward through nozzles 
in the stack. The vapor forced out of these nozzles strikes the gas molecules 
that are present. This forces the gas molecules down toward the outlet near 
the bottom of the pump. Another nozzle in the stack points directly at the 
outlet, and forces the gas molecules out. The vapor condenses on the sides of 
the pump, and the liquid drains down to the bottom. The liquid is boiled again, 
and is reused continuously.

Figure 34  

Diffusion pump parts

Foreline gauge assembly

Foreline gauge cable – part of 
high vacuum control cable

Diffusion pump outlet

KF10/16 seal

Foreline hose 
and hose clamp

KF10/16 clamp

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands