manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 15

Introduction

1

5977B Series MSD Troubleshooting and Maintenance Manual

15

Physical description

The 5977B HES Series MSD housing is approximately 41 cm high, 30 cm wide, 
and 54 cm deep. The weight is 39 kg for the diffusion pump models, and 46 kg 
for the EI/CI turbo pump mainframe. The weight is 41 kg for the EI turbo 
pump mainframe. The standard foreline (roughing) pump weighs an 
additional 11 kg (standard pump), and the dry foreline pump weighs 16 kg. 
The foreline pump is usually located on the floor behind the MSD.

The basic components of the instrument are the:

•

Frame/cover assemblies

•

Vacuum system

•

GC interface

•

Electronics

•

Analyzer

Front Panel LED

The front panel LED allows the operator to monitor the MSD. The LED 
displays the instrument status with color codes and patterns described in 

 “GC 

Control Panel, Power Switch, and Front Panel LED” 

on page 212.

Vacuum gauge

The 5977B HES Series MSD may be equipped with an ion vacuum gauge. The 
Data Acquisition software can be used to read the pressure (high vacuum) in 
the vacuum manifold.

The gauge is 

required

 for chemical ionization (CI) operation.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands