manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 212

212

5977B Series MSD Troubleshooting and Maintenance Manual

8

Electronics

GC Control Panel, Power Switch, and Front Panel LED

GC Control Panel (LCP)

You can view MSD system status and perform some control functions from the 
control panel on a connected 7890B GC. There is no control panel on the MSD.

Functions available through the GC control panel include:

•

Configure network settings of the MSD

•

Change the MSD temperatures

•

View analyzer vacuum or turbo pump speed

•

View foreline pump vacuum

•

Vent or pumpdown the MSD

•

View the firmware version and serial number of the MSD

•

Enable LVDS on the MSD

•

Reboot the MSD

•

Enable BOOTP on the MSD

Power switch

The power switch is part of the electronics module, and is located on the lower 
left of the front of the MSD. It is used to turn the MSD and foreline pump on 
and off.

Front Panel LED

The front panel LED shows the current instrument status through a color 
code, as shown in 

Table 16

 on page 213.

C A U T I O N

Do not switch the MSD off unless it has completed the vent program. Incorrect 
shutdown can seriously damage the MSD.

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands