manualshive.com logo in svg

Agilent Technologies 5977B Series, Troubleshooting And Maintenance Manual

Share
Download
Agilent Technologies 5977B Series Troubleshooting And Maintenance Manual Download Page 71

CI Troubleshooting

3

71

Poor vacuum without reagent gas flow

Excess water in the background

Scan from 10 to 40 

m/z

. A large peak at 

m/z

 19 (>

m/z

 17) indicates water in the 

background. If water is present, allow the instrument to bake out more, and 
flow reagent gas through the lines to purge any accumulated water.

Air leak

Run Methane Pretune. See the 

Operation Manual

. A visible peak at 

m/z

 32 

indicates air in the system. Check for, and correct any leaks. See the 

Leaks

 

section at the beginning of this chapter.

The foreline pump is not working properly

For the standard foreline pump, replace the pump oil. If that does not help, or 
for the dry foreline pump, it may be necessary to replace the pump. Contact 
your local Agilent Technologies Customer Engineer.

The turbo pump is not working properly

Check the pump speed. It should be at least 95%. Contact your local Agilent 
Technologies service representative.

C A U T I O N

Use of ammonia as reagent gas can shorten the life of the foreline pump oil (with 
standard pump) and possibly of the foreline pump itself. 

Summary of Contents for 5977B Series



































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands