TOWA LCM1010, Руководство по эксплуатации

Страница: 534 / 552

А Р Р Е Г
Recipe Data and Constant Data (Handling Module)
Г Recipe Data
Unit Name
Parameter Wait Explanation 1
SLIT MAGAZINE (IN) COUNT Sets the number of stages in the Slit Magazine (IN).
SLIT MAGAZINE (OUT)
COUNT
Sets the number of stages in the Slit Magazine (OUT).
FRAME FEEDER EMPTY FEED
COUNT
Sets the number of stages for which the Slit Magazine (IN) of the
Feeder is empty-fed.
If the number of stages which sets here is continuously empty-fed
Slit Magazine is determined as an emotv magazine and discharged.
FRAME LOADER PREHEAT
TIME
Sets the frame preheating time on the Frame Loader.
*
L/F PH TEMP. SET Sets the temoerature of PreHSater.
Main
L/F PH TEMP. ALARM
Sets the setting of the Preheater,temperature.
If the temperature become higher or'lower than the alarm setting
temperature, the temperature is faulty.
L/F PH TEMP. OFFSET (L)
Sets the offset temperature of the Preheater (left).
If an actual measured value of surface temperature is smaller tha
Preheater setting temperature, this parameter is set to positive
If an actual measured value is larger, the offset value is set to
negative value.
L/F PH TEMP. OFFSET (R)
Sets the offset temperature of the Preheater (right).
If an actual measured value of surface temperature is smaller thai
Preheater setting temperature, this parameter is set to positive
'
If an actual measured value is larger, the offset value is set to
negative value.
S M G J N Uw/Dw
Pos. 1 Frame Send 1st Set the frame transfer position of the 1st stage.
Pos. 1 MG Pitch Sets the Ditch of the Slit Magazine (IN).
SMG_0UT Uw/Dw
[Pos.] Product Receive
1st
Set the frame transfer position of the 1st stage.
Pos. 1 MG Pitch Sets the
d
i tch of the Slit Magaz i ne (IN).
Pos.1 Frame Feed Set the frame feeding Dosition.
[Pos. ] Frame Check
(Existence conf.)
Sets the position to check if there are protruded frames or not.
Sets the position at which the frame check sensor responds to the
(turns OFF).
TPos.1 Frame Check 1 Sets the position for the 1st point of direction check.
[Pos. 1 Frame Check 2 Sets the position for the 2nd point of direction check.
IPos. 1 Frame Check 3 Sets the position for the 3rd point of direction check.
FFD Fw/Bw
FRAME FEEDER FRAME
DIRECTION CHECK USED
CODE
Sets use or unuse of the function to check the direction of the h
Feeder.
This may be set up to three points. (The position data of each po
should be set according to the pa gf eS 5 HANDLER FFD FW/BW.)
Four-digit code is set to determihS^ihicIi position is used.
0000 ■■■ Unused
0001 ■■■ Uses only the 1st (spirit5
->
Set 1 to the 1st digit.
0011 ■■■ Uses the 1st and t h i 2nd'points
->
Set 1 to the 1st
г
2nd digits.
0111 Uses from the J s t to 3rdj>oints
'-*>
Set 1 from the 1s1
the 3rd digitR
T
*
FRAME FEEDER FRAME
DIRECTION CHECK SENSOR
CODE
sets tne UN/un- status o f tne sensor тог tne runction to check m
direction of the Frame’Feeder, when direction check is normally
a
out.
The 0N/0FF status is set by four-digit code. Set 1 when the ON sti
is normal and set 0 when the OFF status is normal to the same digi
which 1 was set in the code for use or unuse.
<EXAMPLE> Use code 0111 (using position 1-3):
The ON status of the sensor is normal at the position 1.
->
S
to the 1st digit.
The OFF status of the sensor is normal at the position 2.
->
to the 2nd digit.
The ON status of the sensor is normal at the position 3.
->
S
tn the 3rd die it
FLD Lw/Rw
[Pos.] Frame Receive L
Sets the frame receiving position (the product sending position o1
Unloader) (left) of the Frame Loader.
[Pos.] Frame Receive R
Sets the frame receiving position (the product sending position o1
Un loader) (right) of the Frame Loader.
FLD Pitch
Adiust 0/C
[Pos.
]
Open Sets the open (frame transfer) position.
T£W A
APPEND