TOWA LCM1010, Руководство по эксплуатации

Страница: 537 / 552

APPENDIX 2
Recipe Date (Press Module) LCM1010
Recipe Data
Unit Name
Parameter Name Explanation
Compress
MOLDING FORCE 1
Sets the molding pressure (the 1st pressure).
Molding operation is carried out by this pressure until the setting
time for shifting 1-2 of molding Dressure.
MOLDING FORCE 2
Sets the molding pressure (the 2nd pressure).
Molding operation is carried out by this pressure after the setting
time has Dassed for shifting 1-2. of molding Dressure.
MOLDING FORCE SHIFT 1-2
Sets the shifting^time from the molding pressure 1 to the molding
Dressure 2.
MOLDING PRESSURE POS
(POS.)
Sets the pressure position of the Clamp.
Curing operation will start when both conditions of the pressure
Dos>ition (oosition) and the Dressure oosition (%) are satisfied.
MOLDING PRESSURE POS (%)
Sets the pressure (Ю at the,pressure p o s i t i o n o f the Clamp.
Curing operation will start when both conditions of the pressure
Dosition (Dosition) and the Dressure position (%) are satisfied.
Clamp
[Spd.] ORG -> RECEIVE
Sets the transfer time from the original position to the receiving
Dosition.
***•'
TPos.l RECEIVE
Sets the Dosition of receiving resin.
[Spd.] R E C E I V E ->
PREHEAT
Sets the transfer time from the receiving position to the preheating
Dosition.
rPos.l PREHEAT
Sets the Dreheating Dosition.
[Spd.] PREHEAT -> FM
START
Sets the transfer time from the preheating position to the FM starting
Dosition.
[Pos.1 FM START Sets the FM starting oosition.
[Spd.] PRS -> FAST DOWN
Sets the transfer time from the pressure position to the fast
descending oosition.
[Pos.1 FAST DOWN Sets the fast descending oosition.
[Spd.] FAST DOWN -> SLOW
DOWN
Sets the transfer time from the fast descending position to the slow
descending oosition.
[Pos.] SLOW DOWN Sets the slow descending position.
[Spd.] SLOW DOWN -> ORG
Sets the transfer time from the slow descending position to the
original Dosition (the frame receiving position).
[Pos.] AIR EJECT OFF
Sets the position at which the Air Eject is turned off in the Air Eject
mode.
[Spd.] FM START ->
PRESSURE (MANUAL)
Sets the speed when ascending by manual operation. (This speed setting
is at or above the FM start oosition.)
Spd. MANUAL UP Sets the soeed when ascending by manual operation.
[Spd. MANUAL DOWN Sets the speed when descending bv manual operation.
Mold Temp.
MOLD TEMP. SET
Sets the temperature of molding die.
MOLD TEMP. ALARM
Sets the alarm setting of molding temperature.
If the molding temperature become higher or lower than the alarm
setting temperature, the molding temperature is faulty.
MOLD TEMP. OFFSET Upper
1(F)
Sets the offset value of molding temperature (upper molding 1).
If an actual measured value of surface temperature is smaller than the
molding setting temperature, this parameter is set to positive value.
If an actual measured value is larger, the oft§.ft)value is set to
negative value.
MOLD TEMP. OFFSET Upper
2(B)
Sets the offset value of molding temperature (upper molding 2).
If an actual measured value of surface temperature is smaller than the
molding setting temperature, this parametlr is set to positive value.
If an actual measured value is larger, the o£fset> value^ifc set to
negative value. .
MOLD TEMP. OFFSET Lower
1(F)
Sets the offset value of molding temperature (loWer molding 1).
If an actual measured value of surface temperature is smaller than the
molding setting temperature, this’parameter is set to positive value.
If an actual measured value is larger, the offset value is set to
negative value.
MOLD TEMP. OFFSET Lower
2(B)
Sets the offset value of molding temperature (lower molding 2).
If an actual measured value of surface temperature is smaller than the
molding setting temperature, this parameter is set to positive value.
If an actual measured value is larger, the offset value is set to
negative value.
APPENDIX 2-6
T3W A