Suzuki GRAND VITARA XL-7 Скачать руководство пользователя страница 343

Страница: 343 / 597

1. Degassing tank
2. Radiator inlet hose
3. Generator belt
4. P / S oil tank
5. P / S pump
6. Terminal “B” and “L” cables
7. Generator

6H-4

CHARGING SYSTEM

3) Using special tool (C), turn roller tensioner counterclockwise to

until special tool (B) becomes free. With roller tensioner kept in
that state, fix it by tightening roller tensioner bolt (1) to specified
torque.

Special tool
(B): 09919-56590 / OUT0000142
(C): 09919-56620

Tightening torque
(a): 50 N

m (5.0 kg-m, 36.5 lb-ft)

4) Remove special tool (B) and (C), turn crankshaft pulley 4 revolu-

tions.

5) Using special tool (B), check that dynamic roller tensioner holes

are aligned. If they are not aligned, repeat step 3) to 5).

UNIT REPAIR OVERHAUL

GENERATOR

DISMOUNTING AND REMOUNTING

Dismount in numerical order indicated in figure.

For remounting, reverse dismounting procedure.

Tighten bolt and nut to specified torque.

Tightening Torque
P / S pump mounting bolt: 25 N

m (2.5 kg-m, 18.0 lb-ft)

Содержание GRAND VITARA XL-7






















































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GRAND VITARA XL-7

Отзывы:

Похожие инструкции для GRAND VITARA XL-7

Бренды по названию

Популярные бренды

Suzuki GRAND VITARA XL-7, Руководство по обслуживанию

Результаты поиска

Содержание GRAND VITARA XL-7

Отзывы:

Похожие инструкции для GRAND VITARA XL-7

Бренды по названию

Популярные бренды