manualshive.com logo in svg

Suzuki GRAND VITARA XL-7, Руководство по обслуживанию


Поделиться
Скачать
background image

7E

DIFFERENTIAL (FRONT)

7E-1

The differential assembly using a hypoid bevel pinion
and gear is installed to the front axle.
4WD control system controls drive force to be trans-
mitted to front axles or not. The reduction ratio varies
depending on transmission.

The differential assembly is decisive in that the drive
power is concentrated there. Therefore, use of genu-
ine parts and specified torque is compulsory. Further,
because of sliding tooth meshing with high pressure
between bevel pinion and gear, it is mandatory to lu-
bricate them by hypoid gear oil.

SECTION 7E

DIFFERENTIAL (FRONT)

NOTE:
For the descriptions (items) not found in this section, refer to the same section of the Service Manual men-
tioned in the FOREWORD of this manual.

CONTENTS

GENERAL DESCRIPTION

7E- 1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

4WD CONTROL SYSTEM

7E- 2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

DIAGNOSIS

7E- 5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

DIAGNOSIS TABLE

7E- 5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

DIFFERENTIAL ASSEMBLY

7E- 5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

4WD CONTROL SYSTEM DIAGNOSTIC FLOW TABLE

7E- 6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

4WD CONTROL CIRCUIT INSPECTION

7E- 8

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

ON-VEHICLE SERVICE

7E- 9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

INSPECTION

7E- 9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

4WD CONTROL SYSTEM

7E- 9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

ACTUATOR

7E-10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

AIR PUMP ASSEMBLY

7E-11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

REMOVAL AND INSTALLATION

7E-12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

DIFFERENTIAL MOUNTINGS

7E-12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

DISMOUNTING

7E-14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

REMOUNTING

7E-15

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

TIGHTENING TORQUE SPECIFICATIONS

7E-16

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

SPECIAL TOOLS

7E-16

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

GENERAL DESCRIPTION

Содержание GRAND VITARA XL-7






















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GRAND VITARA XL-7

Toyota 2012 Rav4 Owner'S Manual preview
2012 Rav4
Бренд: Toyota Страницы: 529
Safe Fleet PRIME DESIGN VCR 326 Assembly Instructions Manual preview
PRIME DESIGN VCR 326
Бренд: Safe Fleet Страницы: 16
Safe Fleet Prime Design VBC PC11 Quick Start Manual preview
Prime Design VBC PC11
Бренд: Safe Fleet Страницы: 8
Safe Fleet Prime Design AR1418 Manual preview
Prime Design AR1418
Бренд: Safe Fleet Страницы: 4
RAM CHASSIS CAB 3500 2017 Quick Reference Manual preview
CHASSIS CAB 3500 2017
Бренд: RAM Страницы: 16
kincrome K12071 Owner'S Assemble And Operating Manual preview
K12071
Бренд: kincrome Страницы: 6
Kia Sportage 2018 Features & Functions Manual preview
Sportage 2018
Бренд: Kia Страницы: 54
Cadillac 2009 CTS Personalization Manual preview
2009 CTS
Бренд: Cadillac Страницы: 20
Cadillac 1993 Seville Owners Literature preview
1993 Seville
Бренд: Cadillac Страницы: 407
Icom RMK-5 Instruction Manual preview
RMK-5
Бренд: Icom Страницы: 20
ULTIMATE SPEED 304669 Instructions For Use And Safety Manuallines preview
304669
Бренд: ULTIMATE SPEED Страницы: 50
Road Ranger H392 Installation Manual preview
H392
Бренд: Road Ranger Страницы: 22
Omix-Ada 11704.05 Owner'S Manual preview
11704.05
Бренд: Omix-Ada Страницы: 6
Audiovox AA-BAT Programming Manual preview
AA-BAT
Бренд: Audiovox Страницы: 3
Victory 4x4 VRKCAP Install Instructions Manual preview
VRKCAP
Бренд: Victory 4x4 Страницы: 9
r.LiNK RL2-MMI3G-GW Manual preview
RL2-MMI3G-GW
Бренд: r.LiNK Страницы: 21
NavLinkz RL4-ELINK Manual preview
RL4-ELINK
Бренд: NavLinkz Страницы: 23
r.LiNK RL2-MMI3G-Q3 Manual preview
RL2-MMI3G-Q3
Бренд: r.LiNK Страницы: 21

Бренды по названию

Популярные бренды

Загрузить еще бренды