manualshive.com logo in svg

Suzuki GRAND VITARA XL-7, Руководство по обслуживанию


Поделиться
Скачать
background image

7B1-32

AUTOMATIC TRANSMISSION (4 A / T)

TABLE A-1: NO GEAR SHIFT TO O/D

SYSTEM DESCRIPTION

TCM does not shift to O / D gear under any of the following conditions.

D

O / D off switch is ON. (“O / D OFF” lamp ON.)

D

4WD low switch is ON.

D

Output shaft speed sensor is in faulty condition. (P0720)

TROUBLESHOOTING

WARNING

D

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

D

Road test should be carried out with 2 persons, a driver and tester, on a level road.

Step

Action

Yes

No

1

Was “A / T DIAGNOSTIC FLOW TABLE” in this
section performed?

Go to Step 2.

Go to “A / T DIAGNOSTIC
FLOW TABLE” in this
section.

2

Check DTC.
Is DTC P0720 detected?

Perform “TROUBLE
DIAGNOSIS TABLE” to
repair and retry.

Go to Step 3.

3

Perform running test under the following 
conditions and check voltage between 
terminal E203-4 of TCM connector and
ground, terminal E203-3 of TCM connector
and ground.

D

O / D off switch is OFF.

D

Selector lever is in “D” range.

D

Transfer lever is in “2H” position.

D

Drive vehicle with 4th gear condition referring
to “GEAR SHIFT DIAGRAM” in this section.

Is each terminal voltage 0 – 1 V?

Faulty shift solenoid
valve, circuit or 
transmission.

“GRN” or “GRN / RED” 
circuit shorted to power
circuit. If wire is OK, go to
Step 4.

4

“O / D” off switch signal inspection.
With ignition switch ON, check voltage 
between terminal E202-3 of TCM connector
and ground.
O / D off switch OFF : 10 – 14 V
O / D off switch ON : 0 – 1 V
Is result as specified?

Go to Step 5.

Faulty O / D off switch or
its circuit.
If OK, substitute a known-
good TCM and recheck.

5

4WD low switch signal inspection
With ignition switch ON, check voltage 
between terminal E202-1 of TCM connector
and ground.
Transfer gear position “4L” or “N”

: 0 – 1 V

Transfer gear position “2H” or “4H” : 10 – 14 V
Is result as specified?

Substitute a known-good
TCM and recheck.

Faulty 4WD low switch or
its circuit.
If OK, substitute a known-
good TCM and recheck.

Содержание GRAND VITARA XL-7






















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GRAND VITARA XL-7

iDataLink maestro Rr Install Manual preview
maestro Rr
Бренд: iDataLink Страницы: 106
Vauxhall Ampera Owner'S Manual preview
Ampera
Бренд: Vauxhall Страницы: 199
Vauxhall INSIGNIA 2017 Owner'S Manual preview
INSIGNIA 2017
Бренд: Vauxhall Страницы: 323
Alpine KCE-G7QI Installation preview
KCE-G7QI
Бренд: Alpine Страницы: 2
Whispbar K896W Fitting Instructions Manual preview
K896W
Бренд: Whispbar Страницы: 15
Code 3 WingMan Installation & Operation Manual preview
WingMan
Бренд: Code 3 Страницы: 8
WABCO TP19108 Installation Manual preview
TP19108
Бренд: WABCO Страницы: 32
B-Speech Sima User Manual preview
Sima
Бренд: B-Speech Страницы: 4
NavLinkz RL2-SC14 Manual preview
RL2-SC14
Бренд: NavLinkz Страницы: 21
SAN HIMA SH-TENT-SY20 User Manual preview
SH-TENT-SY20
Бренд: SAN HIMA Страницы: 7
Paccar Peterbilt SmartAir Operator'S Manual preview
Peterbilt SmartAir
Бренд: Paccar Страницы: 58
Mercedes-Benz 300 SL Operator'S Manual preview
300 SL
Бренд: Mercedes-Benz Страницы: 153
HAUL MASTER 41782 Assembly And Operating Instructions Manual preview
41782
Бренд: HAUL MASTER Страницы: 8
aci ADARAC Aluminum M Series Installation Instructions Manual preview
ADARAC Aluminum M Series
Бренд: aci Страницы: 16
Imiola HAK-POL O/018 Quick Manual preview
O/018
Бренд: Imiola HAK-POL Страницы: 3
Pyle PLDCP3 User Manual preview
PLDCP3
Бренд: Pyle Страницы: 2
Safe Fleet RVS systems RVS-M641 Instruction Manual preview
RVS systems RVS-M641
Бренд: Safe Fleet Страницы: 24
Audi Audi 80 1987 Workshop Manual preview
Audi 80 1987
Бренд: Audi Страницы: 63

Бренды по названию

Популярные бренды

Загрузить еще бренды