manualshive.com logo in svg

Suzuki GRAND VITARA XL-7, Руководство по обслуживанию


Поделиться
Скачать
background image

6-1

ENGINE GENERAL INFORMATION AND DIAGNOSIS (RHZ ENGINE WITH TRIPLE-CONNECTOR ECM)

6-1-1

GENERAL INFORMATION

6-1- 3

. . . . . . . . . . . . . . 

ENGINE DIAGNOSIS

6-1- 3

. . . . . . . . . . . . . . . . . . . 

General Description

6-1- 3

. . . . . . . . . . . . . . . . . . . . 

On-Board Diagnosis

6-1- 3

. . . . . . . . . . . . . . . . . . . . 

Precaution in Diagnosing Trouble

6-1- 3

. . . . . . . . . 

Engine Diagnostic Flow Table

6-1- 3

. . . . . . . . . . . . 

Customer Problem Inspection Form

6-1- 3

. . . . . 

Malfunction Indicator Lamp 

(MIL) Check

6-1- 3

. . . . . . . . . . . . . . . . . . . . . . . . 

Diagnostic Trouble Code (DTC) 

Check

6-1- 3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Diagnostic Trouble Code (DTC) 

Clearance

6-1- 3

. . . . . . . . . . . . . . . . . . . . . . . . . . 

Fail-Safe Table

6-1- 3

. . . . . . . . . . . . . . . . . . . . . . . 

Diagnostic Trouble Code (DTC) Table

6-1- 3

. . . 

Visual Inspection

6-1- 3

. . . . . . . . . . . . . . . . . . . . . 

Engine Basic Check

6-1- 3

. . . . . . . . . . . . . . . . . . 

Engine Diagnosis Table

6-1- 3

. . . . . . . . . . . . . . . 

Inspection of PCM (ECM) and Its

Circuits

6-1- 4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Voltage Check

6-1- 4

. . . . . . . . . . . . . . . . . . . . . 

Resistance Check

6-1- 6

. . . . . . . . . . . . . . . . . . 

Table A-1 MIL Circuit Check

(MIL does not come ON)

6-1- 7

. . . . . . . . . . . . . 

Table A-2 MIL Circuit Check

(MIL remains ON)

6-1- 8

. . . . . . . . . . . . . . . . . . . 

Table A-3 ECM (PCM) Power and

Ground Circuit Check

6-1- 8

. . . . . . . . . . . . . . . . 

DTC P0100 (DTC P0100) MAF

Circuit Malfunction

6-1-10

. . . . . . . . . . . . . . . . . . . 

DTC P0101 (P0100) MAF Sensor

Circuit Range / Performance
Problem

6-1-12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

DTC P0110 IAT Circuit Malfunction

6-1-13

. . . . . 

DTC P0115 (DTC P0115) Engine

Coolant Temp. Sensor Circuit
Malfunction

6-1-15

. . . . . . . . . . . . . . . . . . . . . . . . . 

DTC P0121 (DTC P0120) TP

Circuit Range / Performance
Problem

6-1-16

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

DTC P0604 (P0120) TP Sensor

Monitoring System Malfunction

6-1-16

. . . . . . . . 

DTC P0180 Fuel Temp. Sensor Circuit

Malfunction

6-1-18

. . . . . . . . . . . . . . . . . . . . . . . . . 

DTC P0190 (P0190) Fuel Rail Pressure

Sensor Circuit Malfunction

6-1-19

. . . . . . . . . . . . 

DTC P0191 (P0230) Fuel Rail

Pressure Sensor / Pressure Regulator
Consistency Function

6-1-21

. . . . . . . . . . . . . . . . 

SECTION 6-1

ENGINE GENERAL INFORMATION AND

DIAGNOSIS

(RHZ ENGINE WITH TRIPLE-CONNECTOR ECM)

WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

D

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

D

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).

CONTENTS

Содержание GRAND VITARA XL-7






















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GRAND VITARA XL-7

Calira 811 Manual preview
811
Бренд: Calira Страницы: 14
Panasonic SL-SX451C Operating Instructions preview
SL-SX451C
Бренд: Panasonic Страницы: 2
Panasonic CYRC50U - UNIVERSAL REAR-VIEW CAMERA Manual De Instrucciones preview
CYRC50U - UNIVERSAL REAR-VIEW CAMERA
Бренд: Panasonic Страницы: 20
Panasonic CF-WEB Series Setting Manual preview
CF-WEB Series
Бренд: Panasonic Страницы: 12
Harmar Mobility AL001 Installation And Owner'S Manual preview
AL001
Бренд: Harmar Mobility Страницы: 10
RAM 2015 1500 User Manual preview
2015 1500
Бренд: RAM Страницы: 292
RAM Trucks 1500 User Manual preview
Trucks 1500
Бренд: RAM Страницы: 116
Yamaha Yamaha Rhino 660 Instruction Supplement preview
Yamaha Rhino 660
Бренд: Yamaha Страницы: 3
Kia 2011 optima Owner'S Manual preview
2011 optima
Бренд: Kia Страницы: 385
Calix M5T 187A Assembly Instructions preview
M5T 187A
Бренд: Calix Страницы: 5
Porsche 911 GT3 - Brochure preview
911 GT3 -
Бренд: Porsche Страницы: 51
Whispbar K710W Fitting Instructions For Basic Carrier preview
K710W
Бренд: Whispbar Страницы: 14
Brodit ProClip 804438 Installation Instructions preview
ProClip 804438
Бренд: Brodit Страницы: 2
STC 552-010 Installation Instructions Manual preview
552-010
Бренд: STC Страницы: 6
Whispbar K604W Fitting Instructions Manual preview
K604W
Бренд: Whispbar Страницы: 15
Gator HUDGPS1 Quick Start Manual preview
HUDGPS1
Бренд: Gator Страницы: 2
MAcarbon Ferrari 360 Map Carbon Light Installation Instructions preview
Ferrari 360 Map Carbon Light
Бренд: MAcarbon Страницы: 4
UAZ UAZ-374195 Operating Manual preview
UAZ-374195
Бренд: UAZ Страницы: 90

Бренды по названию

Популярные бренды

Загрузить еще бренды