manualshive.com logo in svg

Suzuki GRAND VITARA XL-7, Руководство по обслуживанию


Поделиться
Скачать
background image

6E3

ENGINE AND EMISSION CONTROL SYSTEM (RHZ ENGINE)

6E3-1

GENERAL DESCRIPTION

6E3- 3

. . . . . . . . . . . . . . 

System Diagram

6E3- 3

. . . . . . . . . . . . . . . . . . . . . 

Air Intake System

6E3- 4

. . . . . . . . . . . . . . . . . . . . . 

Fuel Delivery System

6E3- 5

. . . . . . . . . . . . . . . . . 

Electronic Control System

6E3- 6

. . . . . . . . . . . . . 

System Location Diagram

6E3- 6

. . . . . . . . . . . 

System Wiring Diagram

6E3- 7

. . . . . . . . . . . . . 

ON-VEHICLE SERVICE

6E3-11

. . . . . . . . . . . . . . . . 

Accelerator Cable Adjustment

6E3-11

. . . . . . . . . . 

Idle Speed Inspection

6E3-11

. . . . . . . . . . . . . . . . . 

Air Intake System

6E3-12

. . . . . . . . . . . . . . . . . . . . . 

Vacuum Hose Routing Diagram

6E3-12

. . . . . . 

Intercooler

6E3-13

. . . . . . . . . . . . . . . . . . . . . . . . . 

Throttle Valve Assembly

6E3-14

. . . . . . . . . . . . . 

EGR Throttle Solenoid Valve

6E3-15

. . . . . . . . . 

Vacuum Pump

6E3-15

. . . . . . . . . . . . . . . . . . . . . 

Turbocharger

6E3-16

. . . . . . . . . . . . . . . . . . . . . . 

Boost Pressure Regulator Solenoid

Valve

6E3-18

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Glow Plug

6E3-19

. . . . . . . . . . . . . . . . . . . . . . . . . 

Fuel Delivery System

6E3-20

. . . . . . . . . . . . . . . . . 

Precautions

6E3-20

. . . . . . . . . . . . . . . . . . . . . . . . 

Low Pressure Fuel Supply System

6E3-22

. . . . 

Fuel Pump

6E3-23

. . . . . . . . . . . . . . . . . . . . . . . . . 

Fuel Heater

6E3-23

. . . . . . . . . . . . . . . . . . . . . . . . 

Fuel Injector

6E3-24

. . . . . . . . . . . . . . . . . . . . . . . 

Common Rail

(High Pressure Fuel Injection Rail)

6E3-27

. . . 

Injection Pump

6E3-30

. . . . . . . . . . . . . . . . . . . . . 

Electronic Control System

6E3-32

. . . . . . . . . . . . . 

Engine Control Module (ECM)

6E3-32

. . . . . . . . 

Mass Air Flow Sensor (MAF Sensor)

6E3-34

. . 

Throttle Position Sensor (TP Sensor)

(Accelerator Stroke Sensor)

6E3-35

. . . . . . . . . 

Fuel Temperature Sensor Assembly

6E3-36

. . . 

Fuel (Rail) Pressure Sensor

6E3-38

. . . . . . . . . . 

Engine Coolant Temperature Sensor

(ECT Sensor)

6E3-39

. . . . . . . . . . . . . . . . . . . . . 

VSS

6E3-40

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Camshaft Position Sensor

(CMP Sensor)

6E3-40

. . . . . . . . . . . . . . . . . . . . . 

Crankshaft Position Sensor

(Engine Speed Sensor)

6E3-41

. . . . . . . . . . . . 

Intake Air Pressure Sensor (Manifold

Absolute Pressure Sensor)

6E3-42

. . . . . . . . . 

Radiator Fan Control System

6E3-43

. . . . . . . . . 

Double Relay

6E3-46

. . . . . . . . . . . . . . . . . . . . . . 

Pre Post Heating Relay 

(Control Unit)

6E3-47

. . . . . . . . . . . . . . . . . . . . . 

SECTION 6E3

ENGINE AND EMISSION CONTROL SYSTEM

(RHZ ENGINE)

WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

D

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

D

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).

CONTENTS

Содержание GRAND VITARA XL-7






















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GRAND VITARA XL-7

Vauxhall MOVANO Owner'S Manual preview
MOVANO
Бренд: Vauxhall Страницы: 177
Yakima SkyBox 12 Installation Instructions Manual preview
SkyBox 12
Бренд: Yakima Страницы: 6
Yakima HoldUp Plus2 Manual preview
HoldUp Plus2
Бренд: Yakima Страницы: 18
Tamiya KO PROPO RTF 2002 ESC Manual preview
KO PROPO RTF 2002 ESC
Бренд: Tamiya Страницы: 2
Neuspeed 25.02.22.2 Installation Instructions preview
25.02.22.2
Бренд: Neuspeed Страницы: 2
Menabo JUZA Fitting Instructions Manual preview
JUZA
Бренд: Menabo Страницы: 12
Oldsmobile 2004 Alero Quick Manual preview
2004 Alero
Бренд: Oldsmobile Страницы: 2
Paccar DAF CHARGEMAX 90 User Manual preview
DAF CHARGEMAX 90
Бренд: Paccar Страницы: 40
Cadillac 1999 Escalade Owner'S Manual preview
1999 Escalade
Бренд: Cadillac Страницы: 352
Racelogic Speed & Route Profiler Manual preview
Speed & Route Profiler
Бренд: Racelogic Страницы: 24
Safe Fleet PRIME DESIGN VCR-TC11B Assembly Instructions Manual preview
PRIME DESIGN VCR-TC11B
Бренд: Safe Fleet Страницы: 12
Kogan CERTA CTCVINCVR14A User Manual preview
CERTA CTCVINCVR14A
Бренд: Kogan Страницы: 4
EUFAB 11512 Manual preview
11512
Бренд: EUFAB Страницы: 4
Whispbar K481W Fitting Instructions Manual preview
K481W
Бренд: Whispbar Страницы: 14
Acura 2003 3.2 TL Owner'S Manual preview
2003 3.2 TL
Бренд: Acura Страницы: 347
K&N Engineering Filtercharger 57-9004 Installation Manual preview
Filtercharger 57-9004
Бренд: K&N Engineering Страницы: 4
Honda Element 2004 Owner'S Manual preview
Element 2004
Бренд: Honda Страницы: 219
Buick Enclave Owner'S Manual preview
Enclave
Бренд: Buick Страницы: 394

Бренды по названию

Популярные бренды

Загрузить еще бренды