Suzuki GRAND VITARA XL-7 Скачать руководство пользователя страница 245

Страница: 245 / 597

ENGINE MECHANICAL (RHZ ENGINE)

6A3-47

UNIT REPAIR OVERHAUL

ENGINE ASSEMBLY

REMOVAL

1) Disconnect negative cable at battery.
2) Remove engine hood after disconnecting windshield washer

hose.

3) Remove TP sensor (Accelerator stroke sensor) and intake air

pressure sensor, then remove strut tower bar (1).

4) Drain cooling system.
5) Remove degassing tank and radiator with radiator fan motor as-

sembly.
Refer to “ENGINE COOLING” section.

6) Remove air cleaner outlet hose.
7) Remove intercooler.
8) Remove transmission assembly referring to Section 7A or 7B.

9) Disconnect following electric wires:

Intake air pressure sensor (1)

Camshaft position sensor (2)

Fuel pressure regulator (3)

Glow plug supply wire at the connector

Engine coolant temp. sensor (4)

Fuel pressure sensor (5) wire at the connector

Fuel injectors (6)

Fuel temp. sensor (7)

Injection pump solenoid valve (8)

Generator

Engine oil pressure switch

Double relay (9)

Pre post heating control unit (10)

and then release wire harnesses from clamps.

Содержание GRAND VITARA XL-7






















































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GRAND VITARA XL-7

Отзывы:

Похожие инструкции для GRAND VITARA XL-7

Бренды по названию

Популярные бренды

Suzuki GRAND VITARA XL-7, Руководство по обслуживанию

Результаты поиска

Содержание GRAND VITARA XL-7

Отзывы:

Похожие инструкции для GRAND VITARA XL-7

Бренды по названию

Популярные бренды