manualshive.com logo in svg

Suzuki GRAND VITARA XL-7, Руководство по обслуживанию


Поделиться
Скачать
background image

ENGINE FUEL

6C-3

4) Remove cover (1), corrugated washer (2) and fuel filter ele-

ment (3).

5) Remove fuel filter (4) from bracket (5) by unclipping and lifting

fuel filter.

6) Clean fuel filter.

CAUTION:
Do not use compressed air to fuel filter and its element.

INSTALLATION

1) Install fuel filter (1) to bracket (2).
2) Set fuel filter element (3) and position it correctly.
3) Set corrugated washer (4) on fuel filter.

4) Set cover (1) so that arrow (2) on it is directed toward dash pan-

el.

5) Tighten cover (1) a quarter turn using a 22 mm socket (3).

6) Connect fuel hoses (2) to fuel filter assembly (3).
7) Tighten bleed screw (1).
8) Connect negative cable at battery.
9) Bleed air in system referring to “AIR BLEEDING OF FUEL

SYSTEM” in this section.

10) Start engine and check that there are no fuel leaks.

Содержание GRAND VITARA XL-7






















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GRAND VITARA XL-7

Lange Originals HOIST-A-TOP JL CRANK Installation Instructions Manual preview
HOIST-A-TOP JL CRANK
Бренд: Lange Originals Страницы: 13
Toyota RX450h 2010 Emergency Response Manual preview
RX450h 2010
Бренд: Toyota Страницы: 35
Mercedes-Benz R-Class Owner'S Manual preview
R-Class
Бренд: Mercedes-Benz Страницы: 373
Cadillac 2007 CTS Owner'S Manual preview
2007 CTS
Бренд: Cadillac Страницы: 518
Opel OPEL INSIGNIA Infotainment Manual preview
OPEL INSIGNIA
Бренд: Opel Страницы: 141
Caltrend CV445 Installation Instructions preview
CV445
Бренд: Caltrend Страницы: 2
Audiovox EM-2201 Installation Instructions preview
EM-2201
Бренд: Audiovox Страницы: 1
EGR EGR-3PVE-COLOUR Installation Instructions Manual preview
EGR-3PVE-COLOUR
Бренд: EGR Страницы: 28
Toro 137-1019 Installation Instructions Manual preview
137-1019
Бренд: Toro Страницы: 24
Scosche BTFREQ PRO BTFMPD3SR Manual preview
BTFREQ PRO BTFMPD3SR
Бренд: Scosche Страницы: 16
Calitop Calispace Ocean 80 Assembly Instructions preview
Calispace Ocean 80
Бренд: Calitop Страницы: 5
Lit Lightz RGBW Rock Lights Setup Manual preview
RGBW Rock Lights
Бренд: Lit Lightz Страницы: 3
Hyundai SANTA FE 2020 Getting Started Manual preview
SANTA FE 2020
Бренд: Hyundai Страницы: 19
Mercedes-Benz E55AMG Service Manual preview
E55AMG
Бренд: Mercedes-Benz Страницы: 39
Rugged Ridge 11252.51 Installation Instructions preview
11252.51
Бренд: Rugged Ridge Страницы: 3
Kia Bluetooth Phone System 2010 Reference Manual preview
Bluetooth Phone System 2010
Бренд: Kia Страницы: 16
BMW FXX ATM Emulator User And Installation Manual preview
FXX ATM Emulator
Бренд: BMW Страницы: 5
K40 ELECTRONICS K40 Platinum360 Owner'S Manual preview
K40 Platinum360
Бренд: K40 ELECTRONICS Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды