manualshive.com logo in svg

Siemens RUGGEDCOM RX1510, Руководство пользователя

Siemens RUGGEDCOM RX1510 - мощный промышленный коммутатор с возможностью установки в экстремальных условиях. Безопасный и надежный. Доступен бесплатный пользовательский мануал для скачивания на manualshive.com. Получите подробную информацию о настройке и использовании этого продукта.

Поделиться
Скачать
background image

Chapter 5

Setup and Configuration

RUGGEDCOM ROX II

User Guide

648

Managing GOOSE Tunnels

Section 5.29.5

Managing GOOSE Tunnels

The GOOSE tunnel feature provides the capability to bridge GOOSE frames over a Wide Area Network (WAN).
GOOSE tunnels provide the following features:
• GOOSE traffic is bridged over the WAN via UDP/IP.
• One GOOSE traffic source can be mapped to multiple remote router Ethernet interfaces in mesh fashion.
• To reduce bandwidth consumption, GOOSE daemons may be located at each of the 

legs

 and at the center of a

star network. The centrally located daemon will accept GOOSE packets and re-distribute them.

• Statistics report availability of remote GOOSE daemons, packet counts and Round Trip Time (RTT) for each

remote daemon.

• When the Virtual Router Redundancy Protocol (VRRP) is employed, GOOSE transport is improved by sending

redundant GOOSE packets from each VRRP gateway.

• You can enable GOOSE forwarding by configuring a generic Layer 2 tunnel. When configured, the device

listens for GOOSE packets on one VLAN and forwards them to another VLAN.

The GOOSE protocol is supported by the Layer 2 Tunnel Daemon. The daemon listens to configured Ethernet

interfaces and to the network itself (i.e. for tunnel connections from other daemon instances) on a configurable

UDP port.
The Media Access Control (MAC) destination address of frames received from Ethernet is inspected in order to

determine which GOOSE group they are in. The frames are then encapsulated in network headers and forwarded

(with MAC source and destination addresses intact) to the network as GOOSE packets.
IEC61850 recommends that the MAC destination address should be in the range 01:0c:cd:01:00:00 to

01:0c:cd:01:01:ff.
GOOSE packets received from the network are stripped of their network headers and forwarded to Ethernet

ports configured for the same multicast address. The forwarded frames contain the MAC source address or the

originating device, and not that of the transmitting interface. The VLAN used will be that programmed locally for

the interface and may differ from the original VLAN. The frame will be transmitted with the highest 802.1p priority

level (p4).
Packets received from the network will also be forwarded to any other remote daemons included in the group.
To enable forwarding for GOOSE packets, configure a generic Layer 2 tunnel to listen for GOOSE packets on

one VLAN and forward them to a second VLAN. To configure the generic Layer 2 tunnel for this operation, set the

following for the tunnel:
• Ethernet Interface: select the VLAN on which the GOOSE packets originate
• Ethernet Type: set as 0x88b8
• Remote Daemon: select the VLAN to which to forward the GOOSE packets
The following sections describe how to configure and manage GOOSE tunnels:
•

Section 5.29.5.1, “Viewing the GOOSE Tunnel Statistics”

•

Section 5.29.5.2, “Viewing a List of GOOSE Tunnels”

•

Section 5.29.5.3, “Adding a GOOSE Tunnel”

•

Section 5.29.5.4, “Deleting a GOOSE Tunnel”

Содержание RUGGEDCOM RX1510

























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RUGGEDCOM RX1510

Raven SC1 Accessory Installation Manual preview
SC1
Бренд: Raven Страницы: 27
Raven SC1 Calibration And Operation Manual preview
SC1
Бренд: Raven Страницы: 79
Raven SC1 Calibration & Operation Manual preview
SC1
Бренд: Raven Страницы: 88
JB-Lighting A12 Operating Instructions Manual preview
A12
Бренд: JB-Lighting Страницы: 60
Panasonic DVCPRO P2 Series Brochure & Specs preview
DVCPRO P2 Series
Бренд: Panasonic Страницы: 32
Keithley 263 Quick Reference Manual preview
263
Бренд: Keithley Страницы: 42
Badger Meter ER-10 User Manual preview
ER-10
Бренд: Badger Meter Страницы: 16
Bang & Olufsen BeoPlay A9 Quick Manual preview
BeoPlay A9
Бренд: Bang & Olufsen Страницы: 2
fadini BAYT 980 Instruction Booklet preview
BAYT 980
Бренд: fadini Страницы: 20
U-Line S-11303 Quick Start Manual preview
S-11303
Бренд: U-Line Страницы: 3
U-Line H-3736 Installation Instructions preview
H-3736
Бренд: U-Line Страницы: 2
M-Audio Ozone User Manual preview
Ozone
Бренд: M-Audio Страницы: 48
M-Audio FireWire 410 Quick Start Manual preview
FireWire 410
Бренд: M-Audio Страницы: 19
M-Audio Fast Track Pro User Manual preview
Fast Track Pro
Бренд: M-Audio Страницы: 17
M-Audio MidAir User Manual preview
MidAir
Бренд: M-Audio Страницы: 18
M-Audio X-Session Guía De Inicio Rápido preview
X-Session
Бренд: M-Audio Страницы: 12
M-Audio X-Session User Manual preview
X-Session
Бренд: M-Audio Страницы: 20
Tieline TLR5200 User Manual preview
TLR5200
Бренд: Tieline Страницы: 359

Бренды по названию

Популярные бренды

Загрузить еще бренды