Mitsubishi Electric Q80BD-J61BT11N Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 362

background image

5 - 6 5 - 6

MELSEC

5 PROCEDURE BEFORE STARTING THE DATA LINK

CAUTION



Fix the board by tighten the board-fixing screws within the specified torque range.

Under tightening may cause malfunction. Over tightening may damage the screw
and/or module, resulting in drop, short circuit, or malfunction. For the tightening
torque of the board fixing screws, refer to the manual supplied with the personal
computer.



Always make sure to touch the grounded metal to discharge the electricity

charged in the body, etc., before touching the board.
Failure to do so may cause a failure or malfunctions of the board.



Be sure to shut off all phases of the external power supply used by the system

before installing or removing the board. If all power is not turned off, not doing so
may cause damage to the product.



Install the board to a personal computer which is compliant with PCI standard or

PCI Express

R

standard (Refer to Section 2.3). Failure to do so may cause a

failure or malfunction.



Securely mount the board to the PCI slot of the mounting device.

If the board is not mounted correctly, this may lead to malfunctioning, failure or
cause the board to fall.



When mounting the board, take care not to become injured by the components

that are installed or surrounding materials.



When installing the board, take care not to contact with other boards.



When mounting the board, take care not to become injured by the components

that are installed or surrounding materials.



When turning on the power and operating the module after installation and wiring,

always attach the computer's main cover.
Failure to do so may cause an electric shock.

5.3.4 Setting Channel Numbers

Channel number is set per board, and used to identify the board. 81 is set for the board
channel number as a factory default and the range of 81 to 84 can be set.
Channel numbers being set are used to specify the target boards in setting parameters
and performing the MELSEC data link library function. When using two or more boards
in a single personal computer, set channel numbers not to overlap.

(1) Setting method

Set the channel number with the channel No. setting switch.

Channel No. setting switch

Channel Number

81 82 83 84

1 OFF

ON

OFF

ON

2 OFF

OFF

ON

ON

«
...
112
113
114
115
116
...
»

Содержание Q80BD-J61BT11N











































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Q80BD-J61BT11N

AllShare Cast Dongle

Бренд: Samsung Страницы: 2

Бренд: D-Link Страницы: 14

Бренд: ZETR Страницы: 2

Бренд: Hama Страницы: 4

S5120V3-EI Series

Бренд: H3C Страницы: 54

Бренд: Ublox Страницы: 116

Бренд: Queclink Страницы: 9

Бренд: MiLAN Страницы: 1

PacketShaper PS-S200

Бренд: Symantec Страницы: 2

LoadMaster 1500

Бренд: KEMP Technologies Страницы: 71

kontron COMe-cEL6

Бренд: S&T Страницы: 99

Бренд: Grizzly Страницы: 9

Бренд: C-Smartlink Страницы: 7

Бренд: HighPoint Страницы: 12

Macho Rev. A (BW)

Бренд: Thermalright Страницы: 32

Бренд: Cypress Semiconductor Страницы: 32

Бренд: Transition Networks Страницы: 5

Бренд: TL Audio Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды