Mitsubishi Electric MELSERVO-J4 series, Инструкция по эксплуатации

Страница: 100 / 646

98
3 SIGNALS AND WIRING
3.3 Explanation of power supply system
3.3
Explanation of power supply system
Signal explanations
• For the layout of connector and terminal block, refer to the following.  Page 292 DIMENSIONS
• When using the MR-J4-_GF-RJ servo amplifier with the DC power supply input, refer to the following.
 Page 563 When using the servo amplifier with the DC power supply input
Symbol Connection target
(application) Description
L1/L2/L3 Main circuit power
supply Supply the following power to L1, L2, and L3. For 1-phase 200 V AC to 240 V AC, connect the power supply to L1
and L3. Leave L2 open.
P3/P4 Power factor improving
DC reactor When not using the power factor improving DC reactor, connect P3 and P4. (factory-wired)
When using the power factor improving DC reactor, disconnect P3 and P4, and connect the power factor improving
DC reactor to P3 and P4.
 Page 407 Power factor improving DC reactors
P+/C/D Regenerative option
■
200 V class/100 V class
• MR-J4-500GF(-RJ) or less and MR-J4-40GF1(-RJ) or less
When using a servo amplifier built-in regenerative resistor, connect P+ and D. (factory-wired)
When using a regenerative option, disconnect P+ and D, and connect the regenerative option to P+ and C.
• MR-J4-700GF(-RJ) to MR-J4-22KGF(-RJ)
These servo amplifiers do not have D.
When using a servo amplifier built-in regenerative resistor, connect P+ and C. (factory-wired)
When using a regenerative option, disconnect wires of P+ and C for the built-in regenerative resistor. And then
connect wires of the regenerative option to P+ and C.

Page 335 Regenerative options
■
400 V class
• MR-J4-350GF4(-RJ) or less
When using a servo amplifier built-in regenerative resistor, connect P+ and D. (factory-wired)
When using a regenerative option, disconnect P+ and D, and connect the regenerative option to P+ and C.
• MR-J4-500GF4(-RJ) to MR-J4-22KGF4(-RJ)
These servo amplifiers do not have D.
When using a servo amplifier built-in regenerative resistor, connect P+ and C. (factory-wired)
When using a regenerative option, disconnect wires of P+ and C for the built-in regenerative resistor. And then
connect wires of the regenerative option to P+ and C.

Page 335 Regenerative options
L11/L21 Control circuit power
supply Supply the following power to L11 and L21.
Power Servo amplifier
MR-J4-10GF(-R
J) to MR-J4-200
GF(-RJ) MR-J4-350GF
(-RJ) to MR-J4-
22KGF(-RJ) MR-J4-60GF4
(-RJ) to MR-J4-
22KGF4(-RJ) MR-J4-10GF1
(-RJ) to MR-J4-
40GF1(-RJ)
3-phase 200 V AC to
240 V AC, 50 Hz/60 Hz
L1/L2/L3
1-phase 200 V AC to
240 V AC, 50 Hz/60 Hz L1/L3
3-phase 380 V AC to
480 V AC, 50 Hz/60 Hz L1/L2/L3
1-phase 100 V AC to
120 V AC, 50 Hz/60 Hz L1/L2








  
Power Servo amplifier
MR-J4-10GF(-RJ) to
MR-J4-22KGF(-RJ) MR-J4-60GF4(-RJ) to
MR-J4-22KGF4(-RJ) MR-J4-10GF1(-RJ) to
MR-J4-40GF1(-RJ)
1-phase 200 V AC to
240 V AC, 50 Hz/60 Hz L11/L21
 
L11/L21 
 
1-phase 380 V AC to
480 V AC, 50 Hz/60 Hz 
1-phase 100 V AC to
120 V AC, 50 Hz/60 Hz L11/L21