Mitsubishi Electric FR-F700PJ Series, Инструкция по эксплуатации

Страница: 51 / 356

38
Connection of stand-alone option unit
2.4.3 Connection of the high power factor converter (FR-HC2)
When connecting the high power factor converter (FR-HC2) to suppress power harmonics, perform wiring securely as shown
below. Incorrect connection will damage the FR-HC2 and the inverter.
After making sure that the FR-HC2 is properly connected, set the following parameters.
Pr. 19 Base frequency voltage
Pr. 30 Regenerative function selection (Refer to page 131)

Do not connect anything to the input terminals (R/L1, S/L2, T/L3). Incorrect connection will damage the inverter.

Do not insert an MCCB between the terminals P/+ and N/- (between P and P/+, between N and N/-). Opposite polarity of terminals N/- and P/+ will
damage the inverter.

Use Pr. 178 to Pr. 182 (input terminal function selection) to assign the terminals used for the X10 and RES signals. (Refer to page 134)

Be sure to connect terminal RDY of the FR-HC2 to the X10 signal or MRS signal assigned terminal of the inverter, and connect terminal SE of the
FR-HC2 to terminal SD of the inverter. Without proper connecting, FR-HC2 will be damaged.

Always connect the R/L1, S/L2, and T/L3 terminals of FR-HC2 to the power supply. Operating the inverter without connecting them will
damage FR-HC2.

Do not install an MCCB or MC between the reactor 1 terminals (R/L1, S/L2, T/L3) and FR-HC2 terminals (R4/L14, S4/L24, T4/L34). It will
not operate properly.

Securely perform grounding (earthing) by using the ground (earth) terminal.
 Installation of a fuse is recommended. (Refer to the Instruction Manual of FR-HC2.)
NOTE
 The voltage phases of terminals R/L1, S/L2, and T/L3 and terminals R4/L14, S4/L24, and T4/L34 must be matched.
 Match the control logic (sink logic/source logic) of the FR-HC2 and the inverter. (Refer to page 27 )
 Do not connect a DC reactor (FR-HEL) to the inverter when FR-HC2 is connected.
 Filterpack connection is not available when FR-HC2 is connected.
Parameters referred to
Pr. 30 Regenerative function selection Refer to page 131
ROH2
ROH1
M
P/+ P/+
N/- N/-
X10
SD
RDY
RSO
SE
R/L1
S/L2
T/L3
U
V
W
R1/L11
S1/L21
88R 88R
88S 88S
ROH
SD
R4/
L14
R4/L14
S4/
L24
S4/L24
T4/
L34
T4/L34
R3/
L13
R3/
L13
S3/
L23
S3/
L23
T3/
L33
T3/
L33
R2/
L12
R2/
L12
S2/
L22
S2/
L22
T2/
L32
T2/
L32
R/
L1
S/
L2
T/
L3
R/L1
S/L2
T/L3
RES
*4
*3
*2
*7
*7
*6
*6
*5
*7
*7
*6
*6
*8
*1
*7
*3
MCCB
MC
Reactor1
(FR-HCL21)
Outside box
(FR-HCB2)
Reactor2
(FR-HCL22)
High power
factor converter
(FR-HC2)
Inverter
Earth
(ground)
Motor
Fuse
AC power
supply