Mitsubishi Electric FR-F700PJ Series Скачать руководство пользователя страница 279

Страница: 279 / 356

274

Useful functions

(2) Automatic parameter setting using the operation panel (parameter setting mode)

Operation example

The communication setting parameters for the GOT connection with a PU connector are
automatically set.

Pr.999 setting

Description

Operation in the parameter setting mode

GOT initial setting (PU connector)

(AUTO)



(GOT)



Write "1"

50Hz rated frequency

(AUTO)



(F50)



Write "1"

are displayed alternately ... Why?

The inverter is not in the PU operation mode.

1.Press .

is lit and the monitor (4-digit LED) displays "0." (When

Pr. 79

= "0 (initial setting)")

2. Carry out operation from step 3 again.

PU indicator is lit.

Press to choose the PU operation mode.

The parameter
number read
previously appears.

Operation

Display

Press to choose the

parameter setting mode.

Turn until (AUTO)

appears.

Press to enter the automatic

parameter setting mode.

Press to read the present set
value.
" " appears.

Turn until (GOT) appears.

Screen at power-ON

The monitor display appears.

Turn to read another parameter.

Turn to change it to the set value " ".

Flicker Parameter setting complete!!

Press to set.

Press twice to show the next parameter.

Press to show the setting again.

Содержание FR-F700PJ Series





































































































































































































































































































































































Результаты поиска

Содержание FR-F700PJ Series

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric FR-F700PJ Series, Инструкция по эксплуатации

Результаты поиска

Содержание FR-F700PJ Series

Отзывы:

Бренды по названию

Популярные бренды