Mitsubishi Electric FR-F700PJ Series Скачать руководство пользователя страница 294

Страница: 294 / 356

289

FR-E500 series operation panel (PA02) setting

ARAM

ETE

(b) Method to set frequency only without adjusting gain analog value

(When changing the gain frequency from 60Hz to 50Hz)

Operation Display

Confirm the operation status indicator and

operation mode indicator



The inverter should be at a stop.



The inverter should be in the PU operation mode

(depends on

Press

to choose the parameter setting

mode.

Turn

until

appears.

Press

to display

Turn

until

appears. Turn the dial to

C24 (Pr.923) Frequency setting voltage gain frequency
(built-in potentiometer)

Press

to show the present set value.

Turn

to change the set value to "50.00".

Press

to set.

Flicker...Parameter setting complete!!

(Adjustment completed)



Turn

to read another parameter.



Press

to return to the

indication (step 4).



Press

twice to show the next parameter (

REMARKS



To use the built-in frequency setting potentiometer (

Pr.146

= "0") to operate at a frequency higher than 60Hz, change

C24

and

C25 (Pr.923)

settings. Simply changing the

Pr.1

and

Pr.18

settings does not enable the operation at a frequency higher than

60Hz.



Setting of

Pr. 146, C22 (Pr. 922), C23 (Pr. 922), C24 (Pr. 923), C25 (Pr. 923)

can be performed from the inverter operation panel.

However, it can be performed only when the operation panel PA02 for the FR-E500 is connected.



When setting frequency, parameter, etc. using the operation panel PA02, it is necessary to hold down the

key for 1.5s.



Past four faults are stored in the faults history when the operation panel PA02 is connected.



All faults (E.ILF, E.IOH. E.AIE, E.CDO, E.PTC, E.SOT, E.PID, E.SAF) added to the FR-F700PJ series are displayed as E.14.

The parameter
number read
previously appears.

C0 to C25 settings
are enabled.

Содержание FR-F700PJ Series





































































































































































































































































































































































Результаты поиска

Содержание FR-F700PJ Series

Отзывы:

Похожие инструкции для FR-F700PJ Series

Бренды по названию

Популярные бренды

Mitsubishi Electric FR-F700PJ Series, Инструкция по эксплуатации

Результаты поиска

Содержание FR-F700PJ Series

Отзывы:

Похожие инструкции для FR-F700PJ Series

Бренды по названию

Популярные бренды