Mitsubishi Electric FR-F700PJ Series Скачать руководство пользователя страница 10

Страница: 10 / 356

CONTEN

5.1 Reset method of protective function.............................................. 296
5.2 List of fault or alarm indications..................................................... 297
5.3 Causes and corrective actions ....................................................... 298
5.4 Correspondences between digital and actual characters.............308
5.5 Check first when you have a trouble .............................................. 309

5.5.1

Motor does not start.................................................................................................................... 309

5.5.2

Motor or machine is making abnormal acoustic noise................................................................ 311

5.5.3

Inverter generates abnormal noise............................................................................................. 312

5.5.4

Motor generates heat abnormally............................................................................................... 312

5.5.5

Motor rotates in the opposite direction ....................................................................................... 312

5.5.6

Speed greatly differs from the setting......................................................................................... 312

5.5.7

Acceleration/deceleration is not smooth..................................................................................... 313

5.5.8

Speed varies during operation.................................................................................................... 313

5.5.9

Operation mode is not changed properly ................................................................................... 314

5.5.10 Operation panel display is not operating .................................................................................... 314

5.5.11 Motor current is too large............................................................................................................ 314

5.5.12 Speed does not accelerate......................................................................................................... 315

5.5.13 Unable to write parameter setting............................................................................................... 315

6 PRECAUTIONS FOR MAINTENANCE AND INSPECTION 317

6.1 Inspection items.............................................................................. 318

6.1.1

Daily inspection .......................................................................................................................... 318

6.1.2

Periodic inspection ..................................................................................................................... 318

6.1.3

Daily and periodic inspection...................................................................................................... 319

6.1.4

Display of the life of the inverter parts ........................................................................................ 320

6.1.5

Checking the inverter and converter modules ............................................................................ 320

6.1.6

Cleaning ..................................................................................................................................... 320

6.1.7

Replacement of parts ................................................................................................................. 321

6.2 Measurement of main circuit voltages, currents and powers ....... 324

6.2.1

Measurement of powers ............................................................................................................. 326

6.2.2

Measurement of voltages and use of PT .................................................................................... 326

6.2.3

Measurement of currents............................................................................................................ 327

6.2.4

Use of CT and transducer .......................................................................................................... 327

6.2.5

Measurement of inverter input power factor ............................................................................... 327

6.2.6

Measurement of converter output voltage (across terminals P and N) ...................................... 327

6.2.7

Measurement of inverter output frequency................................................................................. 327

Содержание FR-F700PJ Series





































































































































































































































































































































































Результаты поиска

Содержание FR-F700PJ Series

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric FR-F700PJ Series, Инструкция по эксплуатации

Результаты поиска

Содержание FR-F700PJ Series

Отзывы:

Бренды по названию

Популярные бренды