Mitsubishi Electric FR-F700PJ Series Скачать руководство пользователя страница 295

Страница: 295 / 356

290

Parameter clear/ All parameter clear

4.25 Parameter clear/ All parameter clear

POINT



Set "1" in

Pr.CL Parameter clear, ALLC all parameter clear

to initialize all parameters. (Parameters are not cleared

when "1" is set in

Pr. 77 Parameter write selection



Refer to the extended parameter list on

page 64

for parameters cleared with this operation.

Operation Display

Screen at power-ON

The monitor display appears.

Press

to choose the PU operation mode.

PU indicator is lit.

Press

to choose the parameter setting

mode.

PRM indicator is lit.

(The parameter number read previously appears.)

Turn

until

(

) appears.

Parameter clear

All parameter clear

Press

to read the present set value.

"(initial value) appears.

Turn

to change it to the set value "

Press

to set.

Parameter clear

All parameter clear

Flicker ··· Parameter setting complete!!



Turn

to read another parameter.



Press

to show the setting again.



Press

twice to show the next parameter.

Setting

Description

Not executed.

Set parameters back to the initial values. (Parameter clear sets back all parameters except

calibration parameters, terminal function selection parameters

to the initial values.)

Refer to the

parameter list on page 64

for availability of parameter clear and all parameter clear.

REMARKS

are displayed alternately ... Why?

The inverter is not in the PU operation mode.

PU connector is used.

1. Press

. [PU] is lit and the monitor (4-digit LED) displays "1". (When

Pr. 79

= "0" (initial value))

2. Carry out operation from step 6 again.



Stop the inverter. Parameter clear is unavailable when the inverter is running, and will cause the write disable error.

Содержание FR-F700PJ Series





































































































































































































































































































































































Результаты поиска

Содержание FR-F700PJ Series

Отзывы:

Похожие инструкции для FR-F700PJ Series

Бренды по названию

Популярные бренды

Mitsubishi Electric FR-F700PJ Series, Инструкция по эксплуатации

Результаты поиска

Содержание FR-F700PJ Series

Отзывы:

Похожие инструкции для FR-F700PJ Series

Бренды по названию

Популярные бренды