Mitsubishi Electric FR-F700PJ Series, Инструкция по эксплуатации

Страница: 77 / 356

Parameter list Parameter list
64
4
P
A
RAMETE
R
S
Parameter List
4.2 Parameter list
4.2.1 Parameter list
For simple variable-speed operation of the inverter, the initial setting of the parameters may be used. Set the necessary
parameters to meet the load and operational specifications. Parameter setting, change and check can be made from the
operation panel.
To use the inverter under IPM motor control,
refer to page 83 .
 Symbol in the Remarks column
...Specifications differ according to the date assembled. Refer to page 346 to check the SERIAL number.
 These instruction codes are used for parameter read and write by using Mitsubishi inverter protocol with the RS-485 communication.
(
Refer to page 221 for RS-485 communication)
 "  " indicates valid and "

" indicates invalid of "control mode-based correspondence table", "parameter copy", "parameter clear", and "all parameter clear".
Func-
tion
Parameter Name Setting Range
Minimum
Setting
Increments
Initial
Value
Refer
to
Page
Customer
Setting
Parameter Remarks
Instruction Code
Control Mode-based
Correspondence Table
Parameter
Read Write Extended Copy Clear
All
clear
B
a
sic fu
nctions
 0 Torque boost 0 to 30% 0.1% 6/4/3/2%

92
 0 00 80 0 
 
  
 1 Maximum frequency 0 to 120Hz 0.01Hz 120Hz 101  1 01 81 0      
 2 Minimum frequency 0 to 120Hz 0.01Hz 0Hz 101  2 02 82 0      
 3 Base frequency 0 to 400Hz 0.01Hz 60Hz 103  3 03 83 0  


  
 4 Multi-speed setting (high speed) 0 to 400Hz 0.01Hz 60Hz
106
 4 04 84 0      
 5 Multi-speed setting (middle speed) 0 to 400Hz 0.01Hz 30Hz 106  5 05 85 0      
 6 Multi-speed setting (low speed) 0 to 400Hz 0.01Hz 10Hz
106
 6 06 86 0      
 7 Acceleration time 0 to 3600s 0.1s 5/15s

113  7 07 87 0      
 8 Deceleration time 0 to 3600s 0.1s 10/30s

113  8 08 88 0      
 9 Electronic thermal O/L relay 0 to 500A 0.01A
Rated
inverter
current
119  9 09 89 0      
DC inje
ction
br
ake
10 DC injection brake operation frequency 0 to 120Hz 0.01Hz 3Hz
129
10 0A 8A 0
     
11 DC injection brake operation time 0 to 10s 0.1s 0.5s 129 11 0B 8B 0      
12 DC injection brake operation voltage 0 to 30% 0.1% 4/2%

129 12 0C 8C 0  

  
— 13 Starting frequency 0 to 60Hz 0.01Hz 0.5Hz 116 13 0D 8D 0      
— 14 Load pattern selection 0, 1 1 1 105 14 0E 8E 0 
 
  
JO
G
opera
tion
15 Jog frequency 0 to 400Hz 0.01Hz 5Hz
108
15 0F 8F 0      
16 Jog acceleration/deceleration time 0 to 3600s 0.1s 0.5s 108 16 10 90 0      
— 17 MRS input selection 0, 2, 4 1 0 136 17 11 91 0      
— 18 High speed maximum frequency 120 to 400Hz 0.01Hz 120Hz 101 18 12 92 0      
— 19 Base frequency voltage 0 to 1000V, 8888, 9999 0.1V 9999 103 19 13 93 0 
 
  
Accel
erati
on/
deceleration time
20
Acceleration/deceleration reference
frequency
1 to 400Hz 0.01Hz 60Hz 113 20 14 94 0      
St
al
l
pr
event
ion
22 Stall prevention operation level 0 to 150% 0.1% 120% 96 22 16 96 0      
23
Stall prevention operation level
compensation factor at double speed
0 to 200%, 9999 0.1% 9999 96 23 17 97 0  

  
Parameter Name
Initial
Value Setting
Range
Remarks
160
User group read
selection
9999
9999 Only the simple mode parameters can be displayed.
0
Simple mode and extended mode parameters can be
displayed.
REMARKS
  indicates simple mode parameters.
 The parameters surrounded by a black border in the table allow its setting to be changed during operation even if "0" (initial
value) is set in
Pr. 77 Parameter write selection .
V/F V/F V/F
GP
MFVC
GP
MFVC
GP
MFVC
IPM IPM IPM