Mitsubishi Electric FR-F700PJ Series Скачать руководство пользователя страница 8

Страница: 8 / 356

CONTEN

4.12.3 Reference of the terminal FM (pulse train output) (Pr. 55, Pr. 56) ............................................ 157

4.12.4 Terminal FM calibration (calibration parameter C0 (Pr. 900)) ................................................... 158

4.12.5 How to calibrate the terminal FM when using the operation panel............................................ 159

4.13 Operation selection at power failure and instantaneous power

failure.............................................................................................. 161

4.13.1 Automatic restart after instantaneous power failure/flying start under general-purpose motor control

(Pr. 30, Pr. 57, Pr. 58, Pr. 96, Pr. 162, Pr. 165, Pr. 298, Pr. 299, Pr. 611)
<V/F><GP MFVC> .................................................................................................................... 161

4.13.2 Automatic restart after instantaneous power failure/flying start under IPM

motor control (Pr. 57, Pr. 162, Pr. 611) <IPM>.......................................................................... 166

4.13.3 Power-failure deceleration stop function (Pr. 261) <V/F><GP MFVC> ..................................... 168

4.14 Operation setting at fault occurrence ........................................... 170

4.14.1 Retry function (Pr. 65, Pr. 67 to Pr. 69) ..................................................................................... 170

4.14.2 Input/output phase loss protection selection (Pr. 251, Pr. 872)................................................. 172

4.14.3 Earth (ground) fault detection at start (Pr. 249) ......................................................................... 172

4.14.4 Overspeed detection function (

Pr.374

)....................................................................................... 173

4.15 Energy saving operation and energy saving monitor .................... 174

4.15.1 Optimum excitation control (Pr. 60) ........................................................................................... 174

4.15.2 Energy saving monitor (Pr. 891 to Pr. 899) ............................................................................... 175

4.16 Motor noise, EMI measures, mechanical resonance .................... 181

4.16.1 PWM carrier frequency and Soft-PWM control (Pr. 72, Pr. 240, Pr. 260) ................................. 181

4.16.2 Speed smoothing control (Pr. 653) <V/F><GP MFVC> ........................................................... 182

4.17 Frequency setting by analog input (terminal 2, 4) ........................ 183

4.17.1 Analog input selection (Pr. 73, Pr. 267)..................................................................................... 183

4.17.2 Setting the frequency by analog input (voltage input) ............................................................... 186

4.17.3 Response level of analog input and noise elimination (Pr. 74).................................................. 187

4.17.4 Bias and gain of frequency setting voltage (current)

(Pr. 125, Pr. 126, Pr. 241, C2 (Pr. 902) to C7 (Pr. 905)) ........................................................... 188

4.17.5 Frequency setting signal (current) bias/gain adjustment method .............................................. 190

4.18 Misoperation prevention and parameter setting restriction......... 193

4.18.1 Reset selection/disconnected PU detection/PU stop selection (Pr. 75) .................................... 193

4.18.2 Parameter write disable selection (Pr. 77)................................................................................. 196

4.18.3 Reverse rotation prevention selection (Pr. 78) .......................................................................... 197

4.18.4 Extended parameter display (Pr. 160)....................................................................................... 197

4.18.5 Password function (Pr. 296, Pr. 297)......................................................................................... 198

4.19 Selection of operation mode and operation location.................... 200

4.19.1 Operation mode selection (Pr. 79)............................................................................................. 200

4.19.2 Setting the frequency by the operation panel ............................................................................ 209

4.19.3 Setting the frequency by the operation panel (

Pr. 79

= 3).......................................................... 211

Содержание FR-F700PJ Series





































































































































































































































































































































































Результаты поиска

Содержание FR-F700PJ Series

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric FR-F700PJ Series, Инструкция по эксплуатации

Результаты поиска

Содержание FR-F700PJ Series

Отзывы:

Бренды по названию

Популярные бренды