Mitsubishi Electric FR-F700PJ Series Скачать руководство пользователя страница 198

Страница: 198 / 356

193

Misoperation prevention and parameter setting restriction

ARAM

ETE

4.18 Misoperation prevention and parameter setting restriction

4.18.1 Reset selection/disconnected PU detection/PU stop selection (Pr. 75)

(1) Reset selection



You can select the enable condition of reset function (RES signal, reset command through communication) input.



When

Pr. 75

is set to any of "1, 3, 15, 17", a reset can be input only when the inverter is tripped.

Purpose

Parameter that should be Set

Refer to Page

Limits reset function
Trips when PU is disconnected
Stops from PU

Reset selection/disconnected PU
detection/PU stop selection

Pr. 75

193

Prevention of parameter rewrite

Parameter write disable selection

Pr. 77

196

Prevention of reverse rotation of the motor

Reverse rotation prevention selection

Pr. 78

197

Displays necessary parameters

Display of applied parameters

Pr. 160

197

Parameter restriction with using
password

Password function

Pr. 296, Pr. 297

198

Control of parameter write by
communication

EEPROM write selection

Pr. 342

225

You can select the reset input acceptance, disconnected PU (FR-PU04/FR-PU07) connector detection function and PU
stop function.

Parameter

Number

Name

Initial Value

Setting Range

Description

Reset selection/
disconnected PU detection/
PU stop selection

0 to 3, 14 to 17

For the initial value, reset always enabled,
without disconnected PU detection, and
with PU stop function.



The above parameter can be set when

Pr. 160 Extended function display selection

= "0".

(Refer to page 197)



This parameter allows its setting to be changed during the operation in any operation mode even if "0" (initial value) is set in

Pr. 77 Parameter write

selection

. This setting does not return to the initial value even though the (all) parameter clear is performed.

Pr.

Setting

Reset Selection

Disconnected PU Detection

PU Stop Selection

Reset input normally enabled

When the PU is disconnected,
operation is continued.

Pressing

decelerates the motor

to a stop only in the PU operation
mode.

Reset input is enabled only when the fault
occurs.

Reset input normally enabled

When the PU is disconnected, the
inverter trips.

Reset input is enabled only when the fault
occurs.

(initial value)

Reset input normally enabled

When the PU is disconnected,
operation is continued.

Pressing

decelerates the motor

to a stop in any of the PU, external
and communication operation modes.

Reset input is enabled only when the fault
occurs.

Reset input normally enabled

When the PU is disconnected, the
inverter trips.

Reset input is enabled only when the fault
occurs.

NOTE



When the reset signal (RES) is input during operation, the motor coasts since the inverter being reset shuts off the output.



When reset is performed, cumulative values of electronic thermal O/L relay, and regenerative brake duty are cleared.



The reset key of the PU is only valid when the inverter is tripped, independently of the

Pr. 75

setting.

Содержание FR-F700PJ Series





































































































































































































































































































































































Результаты поиска

Содержание FR-F700PJ Series

Отзывы:

Похожие инструкции для FR-F700PJ Series

Бренды по названию

Популярные бренды

Mitsubishi Electric FR-F700PJ Series, Инструкция по эксплуатации

Результаты поиска

Содержание FR-F700PJ Series

Отзывы:

Похожие инструкции для FR-F700PJ Series

Бренды по названию

Популярные бренды