Mitsubishi Electric FR-F700PJ Series Скачать руководство пользователя страница 5

Страница: 5 / 356

1.1 Product checking and parts identification......................................... 2
1.2 Inverter and peripheral devices ......................................................... 4

1.2.1

Peripheral devices .......................................................................................................................... 5

1.3 Removal and reinstallation of the cover ............................................ 6

1.3.1

Front cover...................................................................................................................................... 6

1.3.2

Wiring cover.................................................................................................................................... 8

1.4 Installation of the inverter and enclosure design.............................. 9

1.4.1

Installation environment for the inverter (Filterpack)....................................................................... 9

1.4.2

Cooling system types for inverter enclosure................................................................................. 11

1.5 Inverter placement (Installation of Filterpack)................................ 11

1.5.1

Installation of the inverter (without Filterpack) .............................................................................. 11

1.5.2

Installation of the inverter and Filterpack (for rear panel installation) .......................................... 12

1.5.3

Installation of Filterpack ................................................................................................................ 13

1.5.4

Installation precautions ................................................................................................................. 15

2 WIRING

2.1 Wiring ................................................................................................ 18

2.1.1

Terminal connection diagram ....................................................................................................... 18

2.2 Main circuit terminal specifications ................................................ 19

2.2.1

Specification of main circuit terminal ............................................................................................ 19

2.2.2

Terminal arrangement of the main circuit terminal, power supply and the motor wiring............... 20

2.2.3

Wiring of the inverter and Filterpack ............................................................................................. 21

2.2.4

Cables and wiring length .............................................................................................................. 22

2.3 Control circuit specifications ........................................................... 25

2.3.1

Control circuit terminal .................................................................................................................. 25

2.3.2

Changing the control logic ............................................................................................................ 27

2.3.3

Wiring of control circuit ................................................................................................................. 29

2.3.4

Connection to the PU connector................................................................................................... 32

2.4 Connection of stand-alone option unit ............................................. 34

2.4.1

Connection of a dedicated external brake resistor (MRS type, MYS type, FR-ABR) ................... 34

2.4.2

Connection of the brake unit (FR-BU2) ........................................................................................ 36

2.4.3

Connection of the high power factor converter (FR-HC2) ............................................................ 38

2.4.4

Connection of the power regeneration common converter (FR-CV) ............................................ 39

2.4.5

Connection of a DC reactor (FR-HEL).......................................................................................... 40

CONTENTS

Содержание FR-F700PJ Series





































































































































































































































































































































































Результаты поиска

Содержание FR-F700PJ Series

Отзывы:

Похожие инструкции для FR-F700PJ Series

Бренды по названию

Популярные бренды

Mitsubishi Electric FR-F700PJ Series, Инструкция по эксплуатации

Результаты поиска

Содержание FR-F700PJ Series

Отзывы:

Похожие инструкции для FR-F700PJ Series

Бренды по названию

Популярные бренды