Mercury HP700 SCi Скачать руководство пользователя страница 95

Страница: 95 / 138

MAINTENANCE

3. Fill the drive unit through the fill/drain hole with Torco MTF

Gear Oil until an air‑free stream of lubricant flows from the

gear oil level hole of gear housing.

7429

150

a -

Top vent screw

b -

Fill/drain screw

Tube Ref

No.

Description

Where Used

Part No.

150

Torco MTF Gear Oil

VI Drive gear

housing

92-849684 1

IMPORTANT: If the filter was replaced, rotate the propeller shaft

at least 80 full revolutions to fill the filter cavity with oil. Recheck

the fluid level and add fluid as necessary.

4. Install vent screw and washer and remove tube from fill/drain

hole. Quickly install the sealing washer and the fill/drain

screw. Tighten securely.

5. Check oil level after first test trial. Add fluid if necessary.

CHANGING TRANSOM INPUT SHAFT BEARING HOUSING

GEAR LUBE (DRIVE-LINE MODELS)

1. Remove the drain plug and drain the oil.
2. Install the drain plug and tighten securely.
3. Remove the plug from the fill hole.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 95 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: