Mercury HP700 SCi Скачать руководство пользователя страница 119

Страница: 119 / 138

COLD WEATHER OR EXTENDED STORAGE

111

Power Package Lay‑up

In addition to the procedures listed in the

Maintenance Chart

this manual, perform the following procedures whenever the power

package will not be used for any extended period of time. Remove

the boat from the water to complete the tasks. Consult your

authorized Mercury Marine dealer.

NOTE: Mercury Marine recommends that the power package

lay‑up be performed by an authorized Mercury Marine dealer.

Flushing the cooling system and preparing the fuel system for

extended storage can be done at the same time. Perform all annual

inspections, lubrication, and fluid changes as outlined in the

Maintenance Charts

of this manual.

NOTICE

Without sufficient cooling water, the engine, the water pump, and

other components will overheat and suffer damage. Provide a

sufficient supply of water to the water inlets during operation.

1. With the boat out of the water, place the drive unit in its full

down position.

2. Remove the propeller to avoid injury while performing the

following procedures.

3. Attach a water hose to the boat's external water pickup.

Supply water to the engine block during operation.

4. Prepare the fuel system for extended storage by mixing the

following in a 23 liter (6 U.S. gal) remote outboard fuel tank:

• 19 liter (5 U.S. gal) premium unleaded 91 octane (R+M)/2

(98 RON) gasoline.

• 1.89 liter (64 fl oz) Premium Plus 2‑cycle TC‑W3 outboard

oil.

• 150 ml (5 fl oz) Fuel System Treatment and Stabilizer or

30 ml (1 fl oz) Fuel System Treatment and Stabilizer

Concentrate.

5. Close the fuel shut off valve if equipped.
6. Disconnect the boat's fuel line from the mechanical fuel pump

inlet.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 119 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: