Mercury HP700 SCi Скачать руководство пользователя страница 135

Страница: 135 / 138

OWNER SERVICE ASSISTANCE

127

• Model and serial number of your outboard
• The name and address of your dealership
• Nature of problem

Mercury Mercruiser Service Offices

For assistance, call, fax, or write. Please include your daytime

telephone number with mail and fax correspondence.

United States

Telephone

Fax

Mercury MerCruiser

3003 N. Perkins Road

Stillwater, OK 74075

(405) 743‑6566

(405) 743‑6570

United States (Mercury Racing)

Telephone

Fax

Mercury Racing

N7480 County Rd. UU

Fond du Lac, WI 54935-9585

(920) 924‑2088

(920) 924‑2096

Canada

Telephone

Fax

Mercury Marine Ltd.

2395 Meadowpine Blvd.

Mississauga, Ontario L5N 7W6

Canada

(905) 567‑6372

(905) 567‑8515

Australia, Pacific

Telephone

Fax

Mercury Marine Australia

132-140 Frankston Road

Dandenong, Victoria 3164

Australia

(61) (3) 9791‑5822

(61) (3) 9793‑5880

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 135 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: