Mercury HP700 SCi Скачать руководство пользователя страница 125

Страница: 125 / 138

COLD WEATHER OR EXTENDED STORAGE

117

a -

Exhaust header balance

rail plastic wing‑nut plugs

(2, Starboard side)

b -

Fuel cooler plastic

wing‑nut plug

c -

Sea water inlet hose ‑

remove from sea pump to

drain

d -

Exhaust header

distribution rail plastic

wing‑nut plugs (2, Port

side, one plug is hidden)

e -

Transmission cooler ‑

remove hose to drain

f -

Power steering cooler

plastic wing‑nut plug

3. Use a stiff piece of wire to clean out any seawater debris from

the drain holes. Do this until the entire system is drained.

4. Lift or bend the hoses to allow water to drain completely.
5. After draining the seawater cooling system, reinstall the drain

plugs.

6. Reconnect the hoses and tighten all hose clamps securely.

USING ANTIFREEZE

For additional protection against freezing and rust in the engine

seawater cooling system when preparing for cold weather or

extended storage, antifreeze containing a rust inhibitor can be run

through the seawater cooling system. Perform the following

procedure for this added protection.

NOTE: A nontoxic and environmentally safe ethylene glycol

antifreeze containing a rust inhibitor must be used when preparing

the seawater portion of the cooling system for cold weather or

extended storage. Be certain to follow the manufacturer's

recommendations.

1. Place approximately 2 gallons of premixed antifreeze into an

appropriate container that will allow the seawater inlet hose to

be placed into the container.

2. If the boat is in the water, close the seawater inlet valve.
3. Loosen the hose clamp and remove the seawater inlet hose

from the downstream side of the valve.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 125 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: