Mercury HP700 SCi Скачать руководство пользователя страница 116

Страница: 116 / 138

MAINTENANCE

108

• Paint the drive unit and transom assembly with a good

quality marine paint or an anti‑fouling paint that does not

contain copper, tin, or any other material that could conduct

electrical current. Do not paint drain holes, anodes, or items

specified by the boat manufacturer.

Additional Corrosion Prevention Tips

• Spray the power package components on the inside of the

boat every two to three weeks with Corrosion Guard to

protect the finish from dulling and corrosion. External

power package components may also be sprayed.

Tube Ref

No.

Description

Where Used

Part No.

120

Corrosion Guard

Power package

92-802878 55

• All lubrication points, especially the steering system and

shift and throttle linkages, should be kept well lubricated.

• Flush the raw water portion of the cooling system after each

use.

MERCATHODE

To protect the larger sterndrive engine packages from galvanic

corrosion, purchase this MerCathode kit, (PN 42600A18).

Galvanic Isoltaors

Low‑voltage galvanic current can be passed between neighboring

boats through the shore‑power electrical transmission lines.

Galvanic isolators block this low voltage current that can destroy

your power package. Ensure that the isolator is of high quality, and

rated to handle the amperage load of the boat and the shore‑power

connected to it.

Battery

All lead acid batteries discharge when not in use. Recharge every

30 to 45 days, or when specific gravity drops below battery

manufacturer's specifications.
Refer to specific instructions and warnings accompanying your

battery. If this information is not available, observe the following:

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 116 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: