Mercury HP700 SCi Скачать руководство пользователя страница 14

Страница: 14 / 138

WARRANTY INFORMATION

No individual or entity, including Mercury Marine authorized

dealers, has been given authority by Mercury Marine to make any

affirmation, representation or warranty regarding the product,

other than those contained in this limited warranty, and if made,

shall not be enforceable against Mercury Marine. For additional

information regarding events and circumstances covered by this

warranty, and those that are not, see the

Warranty Coverage

section of the

Operation and Maintenance Manual

, incorporated

by reference into this warranty.
DISCLAIMERS AND LIMITATIONS THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE ARE EX‑PRESSLY DISCLAIMED. TO THE EXTENT

THAT THEY CANNOT BE DISCLAIMED, THE IMPLIED

WARRANTIES ARE LIMITED IN DURATION TO THE LIFE OF

THE

EXPRESS

WARRANTY.

INCIDENTAL

AND

CONSEQUENTIAL DAMAGES ARE EXCLUDED FROM

COVERAGE UNDER THIS WARRANTY. SOME STATES/

COUNTRIES DO NOT ALLOW FOR THE DISCLAIMERS,

LIMITATIONS AND EXCLUSIONS IDENTIFIED ABOVE, AS A

RESULT, THEY MAY NOT APPLY TO YOU. THIS WARRANTY

GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO

HAVE OTHER LEGAL RIGHTS WHICH VARY FROM STATE TO

STATE AND COUNTRY TO COUNTRY.

Products Sold to Government Agencies

Contact the Mercury Racing Sales Department for a copy of the

Government Agencies Warranty Packet Kit which explains the

conditions required for government agencies to receive warranty

when purchasing Mercury Racing Outboard or Sterndrive

product.
Mercury Racing Sales Department

N7840 County Road UU

Fond du Lac, WI 54935

920-921-5330

Fax 920-921-6533

Warranty Against Corrosion (Worldwide)

IMPORTANT: Corrosion failure warranty is not available for this

product.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 14 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: