Mercury HP700 SCi Скачать руководство пользователя страница 46

Страница: 46 / 138

OPERATION

3. A 15 amp fuse, located on the engine's electrical panel,

protects the keyswitch power. Check for an open fuse if the

key is turned to "START" and nothing happens (and circuit

breaker is not tripped).

10138

a -

Ignition switch "I" terminal lead

4. The power trim pump is internally protected from thermal

overload. If it overheats, it will shut off, allowing itself to cool

and then reset. However, it is recommended that the power

trim system be installed with additional overload protection.

Therefore, the power trim may be protected from overload by

a 110 amp fuse in the power supply to the pump and a 20 amp

in‑line fuse to the switch power.

5. A 110 amp fuse is located on the starter.

10309

a -

Positive (+) battery cable

b -

110 amp fuse

c -

Starter

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 46 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: