Mercury HP700 SCi Скачать руководство пользователя страница 34

Страница: 34 / 138

SPECIFICATIONS

DRIVE UNIT AND TRANSOM ASSEMBLY IDENTIFICATION

25175

a -

Transom serial number

b -

NXT¹ serial number, drive

overall ratio and rotation

c -

NXT¹/SSM drive rotation

d -

NXT¹/SSM serial number

and drive overall ratio

SERIAL NUMBERS RECORD

The serial numbers are the manufacturer's keys to numerous

engineering details that apply to your Mercury Marine power

package. When contacting your authorized Mercury Marine dealer

about service, always specify model and serial numbers.

1. The engine serial number is printed on the placard located on

the heat exchanger.

2. The Transom serial number is located on the starboard side

of the outer transom assembly under the plastic transom

cover.

NXT¹ -

Drive rotation, overall ratio, and serial number are all

located under the cover or tie bar plate on the top of the upper

driveshaft housing.

NXT¹/SSM -

The serial number is located on the starboard

underside of the upper gear housing.

NXT¹/SSM -

The gear ratio is stamped on the bolt head

located next to the serial number label.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 34 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: