Mercury HP700 SCi Скачать руководство пользователя страница 19

Страница: 19 / 138

WARRANTY INFORMATION

a. Hoses, clamps, fittings, tubing, sealing gaskets or

devices, and mounting hardware

b. Pulleys, belts and idlers
c. Vacuum, temperature, check, and time sensitive valves

and switches

d. Electronic Controls

STAR LABEL

Engines are labeled with one of the following star labels.
The Symbol for Cleaner Marine Engines Means:
Cleaner Air and Water ‑ for a healthier lifestyle and environment.
Better Fuel Economy ‑ burns up to 30‑40 percent less gas and oil

than conventional carbureted two‑stroke engines, saving money

and resources.
Longer Emission Warranty ‑ Protects consumer for worry free

operation.
IMPORTANT: Although labeled as Two or Three Star, the

engine(s) in this boat meet the requirements of the Air Resources

Board's 2009 and later exhaust emission standards for High

Performance Sterndrive and Inboard Marine Engines with power

> 373 kW.

22531

One Star ‑ Low Emission
The One Star label identifies engines that meet the

Air Resources Board's 2001 exhaust emissions

standards. Engines meeting these standards have

75% lower emissions than conventional

carbureted two‑stroke engines. These engines are

equivalent to the U.S. EPA's 2006 standards for

marine engines.

IDA

22532

Two Stars ‑ Very Low Emission
The Two Star label identifies engines that meet the

Air Resources Board's Personal Watercraft and

Outboard marine engine 2004 exhaust emissions

standards. Engines meeting these standards have

20% lower emissions than One Star ‑ Low

Emission engines.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 19 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: