Mercury HP700 SCi Скачать руководство пользователя страница 13

Страница: 13 / 138

WARRANTY INFORMATION

WHAT IS NOT COVERED

This limited warranty does not cover routine maintenance items,

tune ups, adjustments, normal wear and tear, damage caused by

abuse, abnormal use, use of a propeller or gear ratio that does not

allow the engine to run in its recommended wide‑open‑throttle

RPM range (see the

Operation and Maintenance Manual

operation of the product in a manner inconsistent with the

recommended operation/duty cycle section of the

Operation and

Maintenance Manual

, neglect, accident, submersion, improper

installation (proper installation specifications and techniques are

set forth in the installation instructions for the product), improper

service, use of an accessory or part not manufactured or sold by

us, operation with fuels, oils or lubricants which are not suitable for

use with the product (see the

Operation and Maintenance

Manual

), alteration or removal of parts, water entering the engine

through the fuel intake, air intake or exhaust system, or damage to

the product from insufficient cooling water caused by blockage of

the cooling system by a foreign body, running the engine out of

water, mounting the engine too high on the transom, or running the

boat with the engine trimmed out too far. The commercial use of

the product, defined as any work or employment related use of the

product, or any income generating use of the product, even if such

use is only occasional, will void the warranty. Use of the product

for racing or other competitive activity, at any point, even by a prior

owner of the product, voids the warranty. Expenses related to

haul‑out, launch, towing, storage, telephone, rental,

inconvenience, slip fees, insurance coverage, loan payments, loss

of time, loss of income, tournament fees, club fees, prize money

or any other type of incidental or consequential damages are not

covered by this warranty. Also, expenses associated with the

removal and/or replacement of boat partitions or material caused

by boat design for access to the product are not covered by this

warranty.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 13 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: