Mercury HP700 SCi Скачать руководство пользователя страница 137

Страница: 137 / 138

ORDERING LITERATURE

129

United States and Canada

Before ordering literature, please have the following information

about your power package available:

Engine
Model:

Horsepower:

Serial
Number:

Model year:

For information on additional literature that is available for your

particular Mercury/MerCruiser power package and how to order

that literature contact your nearest dealer or contact:

MERCURY MARINE

Telephone

Fax

Mail

(920) 929‑5110 (920) 929‑4894

Mercury Marine

Attn: Publications Department

P.O. Box 1939

Fond du Lac, WI 54936-1939

Outside The United States and Canada

Before ordering literature, please have the following information

about your power package available:

Engine
Model:

Horsepower:

Serial
Number:

Model year:

Contact your nearest dealer or Marine Power Service Center for

information on additional literature that is available for your

particular Mercury/MerCruiser power package and how to order

that literature.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 137 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: