Mercury HP700 SCi Скачать руководство пользователя страница 131

Страница: 131 / 138

TROUBLESHOOTING

123

Engine Coolant Temperature Too High

Possible Cause

Remedy

Seacock closed.

Open.

Serpentine belt loose or in poor condition.

Replace or adjust belt.

Recirculating pump defective.

Replace.

Seawater pickups obstructed.

Inspect.

Faulty thermostat.

Replace.

Oil cooler cores plugged with foreign

material.

Clean cooler cores.

Heat exchanger restricted.

Backflush.

Faulty seawater pickup pump.

Repair.

Seawater discharge restricted or plugged.

Clean exhaust elbows.

Faulty gauges or senders.

Test with shop gauges; test

senders.

Aerated water supply to water pick‑up.

Place water pick‑up in a

non‑aerated water supply.

Low Engine Oil Pressure

Possible Cause

Remedy

Insufficient oil in system.

Check and add oil.

Excessive oil in system (causing it

to become aerated).

Check and bring oil to required level. Check

for cause of excessive oil (improper filling,

defective fuel pump, etc.).

Diluted or improper viscosity oil.

Change oil and oil filter, using correct grade

and viscosity oil. Determine cause for

dilution (excessive idling, faulty fuel pump,

etc.).

Faulty gauge or sender.

Test with mechanical shop gauge; test

sender.

Excessive oil temperature.

Faulty oil thermostat.

Engine mechanical: oil pump,

excessive bearing clearance, etc. Repair as necessary.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 131 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: