Mercury HP700 SCi Скачать руководство пользователя страница 21

Страница: 21 / 138

GENERAL INFORMATION

Boater's Responsibilities

The operator (driver) is responsible for the correct and safe

operation of the boat and safety of its occupants and general

public. It is strongly recommended that each operator (driver) read

and understand this entire manual before operating the power

package.
Be sure at least one additional person on board is instructed in the

basics of starting and operating the power package, and boat

handling in case the driver is unable to operate the boat.

Boat Horsepower Capacity

WARNING

Exceeding the boat's maximum horsepower rating can cause

serious injury or death. Overpowering the boat can affect boat

control and flotation characteristics or break the transom. Do not

install an engine that exceeds the boat's maximum power

rating.

Do not overpower or overload your boat. Most boats will carry a

required capacity plate indicating the maximum acceptable power

and load as determined by the manufacturer following certain

federal guidelines. If in doubt, contact your dealer or the boat

manufacturer.

U.S. COAST GUARD CAP ACITY
MAXIMUM HORSEPOWER XXX

MAXIMUM PERSON
CAPACITY (POUNDS)

XXX

MAXIMUM WEIGHT
CAPACITY

XXX

26777

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 21 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: