Mercury HP700 SCi Скачать руководство пользователя страница 126

Страница: 126 / 138

COLD WEATHER OR EXTENDED STORAGE

118

4. Place the hose into the container of premixed antifreeze. The

antifreeze mixture should be at the correct concentration level

to protect the engine to the lowest temperature to which it will

be exposed during cold weather or extended storage.

13180

a -

Seawater inlet valve

b -

Disconnect the hose at

the valve and place into

container of antifreeze

c -

Sea strainer

d -

To the seawater pump

e -

Boat hull

f -

Seawater pickup

5. Operate the engine at idle until antifreeze is expelled from the

exhaust manifolds of the engine.

NOTE: The antifreeze can be run through the engine while

running the fuel fogging mixture as explained in

Cold Weather or

Extended Storage - Power Package Lay-up

6. Stop the engine and reconnect the seawater hose.
7. If the boat is in the water, do not open the seawater inlet valve

until the power package is ready for recommissioning.

Battery Storage

Whenever the battery will be stored for an extended period of

time, be sure the cells are full of water and the battery is fully

charged and in good operating condition. It should be clean and

free of leaks. Follow the battery manufacturer's instructions for

storage.

Power Package Recommissioning

IMPORTANT: Do not install the battery until all engine

maintenance is completed.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 126 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: