Mercury HP700 SCi Скачать руководство пользователя страница 111

Страница: 111 / 138

MAINTENANCE

103

Final Fuel Filter

WARNING

Fuel is flammable and explosive. Ensure the key switch is off and

the lanyard is positioned so that the engine cannot start. Do not

smoke or allow sources of spark or open flame in the area while

servicing. Keep the work area well ventilated and avoid

prolonged exposure to vapors. Always check for leaks before

attempting to start the engine and wipe up any spilled fuel

immediately.

1. Disconnect the fuel line at the outlet side of the fuel filter.

25183

a -

Final Fuel filter

b -

Fuel filter outlet

2. Disassemble the fuel filter assembly by unscrewing the filter

outlet from the fuel filter cannister.

3. Remove the filter element and O‑ring from the filter outlet and

discard. Do not remove the spring from the cannister unless

replacement is necessary.

4. Apply High Pressure grease sparingly to the O‑ring and

threads of the outlet and fuel line fitting.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 111 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: