Mercury HP700 SCi Скачать руководство пользователя страница 36

Страница: 36 / 138

SPECIFICATIONS

Engine Operating Limitations (HP700)

Maximum wide open throttle (W.O.T.) RPM 4800 ‑ 5300 RPM

Rev limit

5400 RPM

Idle RPM in gear

700 RPM

Idle RPM out of gear

750 RPM

Maximum fuel system flow rate

256 L/hr (68 gals/hr) at 5200 RPM

Fuel pressure at idle

4071 ‑ 421 kPa (59 ‑ 61 psi)

Fuel pressure at W.O.T.

462 ‑ 483 kPa (68 ‑ 72 psi)

Coolant thermostat is fully open at

temperature

70° C (158° F)

Minimum water pressure supplied to the

engine

207 kPa (30 psi) at 5200 RPM

Maximum water pressure supplied to the

engine

290 kPa (42 psi) at 5200 RPM

Minimum oil pressure @ idle (Hot)

100 kPa (14.5 psi)

Minimum oil pressure at 5200 RPM (Hot)

379 ‑ 448 kPa (55 ‑ 65 psi)

Maximum oil temperature at 5200 RPM

(Hot)

88° C (190° F)

Fuel Requirements

Use a major brand of unleaded gasoline, preferably without

alcohol. Mercury Marine recommends fuels that contain fuel

injector cleaner for added internal cleanliness.

WARNING

Fuel leakage is a fire or explosion hazard, which can cause

serious injury or death. Periodically inspect all fuel system

components for leaks, softening, hardening, swelling, or

corrosion, particularly after storage. Any sign of leakage or

deterioration requires replacement before further engine

operation.

1. Engines are equipped with an ignition system that has a built‑in 5400 RPM

rev limiter. Engine is performing normally if it will not exceed this RPM.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 36 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: