Mercury HP700 SCi Скачать руководство пользователя страница 56

Страница: 56 / 138

OPERATION

3. If the engine is cold, make sure the engine is idling smoothly

before operating the boat.

4. After the engine has warmed up, check the water temperature

gauge to ensure that the engine temperature is not abnormally

high. If it is, stop the engine immediately and determine

cause.

5. Ensure that the charging system is functioning correctly.
6. Observe the power package for fuel, oil, water, and exhaust

leaks.

Operation Chart

Before Starting

Open the engine hatch.
Turn battery switch "ON," if equipped.
Operate bilge blowers, if equipped.
Open fuel shut off valve.
Open seacock, if equipped.
Perform all other checks specified by your dealer and/or

boat builder.

After Starting

Observe all gauges to check condition of engine. If not

normal, stop engine.
Check for fuel, oil, water, fluid and exhaust leaks, etc.
Check shift and throttle control operation.
Check steering operation.

While Underway

Observe all gauges to monitor engine condition.

After Stopping

Shift to neutral. Turn ignition key "OFF."
Turn battery switch "OFF," if equipped.
Close fuel valve.
Close seacock.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 56 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: