Mercury HP700 SCi Скачать руководство пользователя страница 75

Страница: 75 / 138

MAINTENANCE

1. Check the coolant level in the coolant reservoir when the

engine is cold. Coolant should be at the "COLD FULL" line

marked on the front of the reservoir or to the top of the raised

bosses on the back of the reservoir. Add specified coolant by

turning the cap 1/4 turn to allow any pressure to escape

slowly, then push down and turn the cap all the way off.

COLD FILL

10140

122

a -

Coolant reservoir cap

b -

Cold full decal on the front of the reservoir

c -

Cold full raised bosses on the back of the reservoir

Tube Ref

No.

Description

Where Used

Part No.

122

Extended Life

Antifreeze/Coolant

Closed cooling

system

92-877770K1

2. If coolant is low, inspect the coolant recovery system for

leaks.

3. Inspect the cap for damage and replace if necessary.

CHECKING POWER TRIM PUMP FLUID

IMPORTANT: Check oil level with sterndrive unit in the full down/

in position.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 75 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: